[nmcli] Where is the configuration file of device (redhat 7) Post: 302993246

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

x window configuration for redhat 6.0

I recently tried to install redhat 6.0 on my IBM desk top. Everything was fine except the x window. After the installation, I logged in, the icons and graphics were so big that I even could not read a complete message in one screen. I did not find any helpful tool in the control panel to help me...

2. UNIX for Dummies Questions & Answers

RedHat display cpu configuration

Hello people ! Does anyone knows how can I get the CPU configuration in the RedHat Box ??? I need know the frequence of cpu and how much cpu(s) in my box ... Thank you, Witt

3. Red Hat

qmail configuration in redhat linux - doubts

hi, How to Install & configure the qmail in redhat linux? and also how to get the free qmail package? I know the sendmail configuration in redhat linux. What is the features of qmail compared with sendmail? Regards, Jones

4. Red Hat

Dns configuration error in Redhat

Dear All I want to configure DNS in redhat linux. i am following these steps but when i restart the services it is showing status failed. Please any body can help me on urgent basis. #service named restart Stopping named: Starting named: ---------Edited in named.conf...

5. UNIX for Advanced & Expert Users

where do the configuration files from Redhat (fedora) authconfig-tui reside?

I have tried moving out the /etc/ldap.conf as well as /etc/openldap/ldap.conf files. I have LDAP Authentication turned on in the TUI. It lets me define a host and base, but the entries are not saved to the above files. /etc/sysconfig/authconfig has a bunch of environmental variables, but none...

6. Red Hat

DELL M910 with RedHat Linux 5.5 getting "Buffer I/O error on device sdd"

Dear Guru, IHAC who is using Redhat Linux 5 on DELL M910. When system bootup, it show "Buffer I/O error on device sdd" error message. Below is the "dmesg" output. The scenario is: If more external FC SAN disk LUN add, the device would change other name. So it will impact the raw device...

7. Shell Programming and Scripting

Help with Backup Shell Script for Network Device Configuration backup

HI all, im new to shell scripting. need your guidence for my script. i wrote one script and is attached here Im explaining the requirement of script. AIM: Shell script to run automatically as per scheduled and backup few network devices configurations. Script will contain a set of commands...

8. Red Hat

Unable To Activate Ethernet Network Device in RHEL 5.5 - e100 device eth0 does not seem to be presen

Hi All, Could anyone please help to resolve the below problem. I installed RHEL5.5 in my desktop.But when i try to activate the ethernet connection then it gives me the error. I spent 2 days for the above and go through with several suggestion found by googling. But no luck. ...

9. AIX

0514-516 Device Configuration Database Lock Service

Hello guys, on one of our AIX VIO LPARs I can not remove hdiskpower devices, which seemed to presented to the VIO in an incorrect way and behaviour (not all paths can be seen, pseudo device name is unknown etc.) Therefor I decided to deattach the hdiskpower device from PowerPath controll by: ...

LEARN ABOUT SUSE

ifcfg-wireless

IFCFG(5)						       Network configuration							  IFCFG(5)

NAME

       ifcfg-wireless - wireless LAN network interface configuration

SYNOPSIS

       /etc/sysconfig/network/ifcfg-wlan-*
       /etc/sysconfig/network/ifcfg-type-wlan

GENERAL

       Wireless  networks  need  some additional configuration data compared to ethernet ones. Therefore additional variables for ifcfg files were
       introduced.  All wireless LAN specific variables are described in the ifcfg template file /etc/sysconfig/network/ifcfg.template. It is pos-
       sible to configure more than one wireless network accepted for association. To achieve this add suffix _1 to all wireless variables for the
       second network, _2 for the this, and so on. Example: WIRELESS_ESSID_1="second_net" You can have up to  ten  wireless  networks  configured.
       Some  wireless  variables  are not applicable to a single wireless network but are global to the interface. The description of the variable
       points this out.

BUGS

       Please report bugs at <http://www.suse.de/feedback>

AUTHOR

       Christian Zoz <zoz@suse.de> -- ifup script
       Michal Svec <msvec@suse.cz> -- ifup script
       Bjoern Jacke -- ifup script
       Mads Martin Joergensen <mmj@suse.de> -- ifup manual page
       Michal Ludvig <mludvig@suse.cz> -- tunnel support
       Joachim Gleissner <jg@suse.de> -- wireless support

SEE ALSO

       ifup(8).

sysconfig							   December 2005							  IFCFG(5)