Hey all,
I ran some simulations, of which the output is 100s of files. I've used grep to extract the vital information needed from the files. This has made my task somewhat easier. But I still need to perform some mathematical calculations (average and geometrical average) on the results of the... (9 Replies)
Hi,
I've been trying to replace the numbers in the first column of my text file with all ones, unless the number is equal to 8. I have this:
1 1 11 123 258
2 1 9 135 175
1 1 15 143 274
8 1 13 153 172
8 1 13 154 166
8 1 13 154 167
3 1 15 237 255
4 1 15 243 202
1 1 13 133 166... (4 Replies)
Hi,
I have lines in some files that look exactly as below, and the line numbers they occur in are always the same. (Lines 136-139)
W 0.00000000 0.00000000 2.00000000
W 0.50000000 0.50000000 2.50000000
W 0.00000000 0.00000000 3.00000000
W 0.50000000 0.50000000 3.50000000
I'd like to... (0 Replies)
Hi people :)
I'm learning shell scripting using bash and I want to generate 4 floating point number with 5 decimal places and write them to a file and a variable. I've done all this except the $RAMDOM enviroment variable does not generate a float number but a integrer.
I hope you could... (3 Replies)
Hi,
I need to match up some numbers in one file to the closest numbers in other file and produce an output file.
File one (f1.txt) is laid out like this
PCode Lon Lat
AB10 1AA 57.148235 -2.096648
BB2 3JD 53.728563 -2.47852
LU4 9ET... (4 Replies)
Hello All,
I was wondering if someone might know how to do this. I have a word list that is format like the example below. I need to take away the :number after that... is there some kind of command I could use to remove them?
123456:5562
password:1507
123456789:989
qwerty:877... (7 Replies)
Hello everyone,
I need your assistance with bash.
I want to sum up some numbers, that's not the big problem i think, but the values i want to some depending on another number.
For example, I have a file with some rows of content.
Number 1, Number 2, other content.
I want to sum up number... (4 Replies)
Hello,
I have the following script
while read id fraction
do
sambamba -h -f bam -t 10 --subsampling-seed=50 -s $frac ${id}.bam -o ${id}.out.bam
done < fraction.txt
where fraction.txt has two columns (id,fraction) and 50 rows
I am unable to run this as bash is not able to read the second... (2 Replies)
I have the following code snippet in bash
if ]; then
minm=`echo "$diff" | bc`
fi
It works well for most of the cases. However lets say diff is -0.17 and minm is -0.0017. In such a case the comparison seems to fail. Is the correct way to compare a mixture of positive and... (12 Replies)
Hi,
is possible in bash script change numbers "01140" to "0 hours, 11 minutes, 40 seconds" ?
Thanks! (8 Replies)
Discussion started by: simpsonss
8 Replies
LEARN ABOUT DEBIAN
pnmpsnr
pnmpsnr(1) General Commands Manual pnmpsnr(1)NAME
pnmpsnr - compute the difference between two portable anymaps
SYNOPSIS
pnmpsnr [pnmfile1] [pnmfile2]
DESCRIPTION
Reads two PBM, PGM, or PPM files, or PAM equivalents, as input. Prints the peak signal-to-noise ratio (PSNR) difference between the two
images. This metric is typically used in image compression papers to rate the distortion between original and decoded image.
If the inputs are PBM or PGM, pnmpsnr prints the PSNR of the luminance only. Otherwise, it prints the separate PSNRs of the luminance, and
chrominance (Cb and Cr) components of the colors.
The PSNR of a given component is the ratio of the mean square difference of the component for the two images to the maximum mean square
difference that can exist betwee any two images. It is expressed as a decibel value.
The mean square difference of a component for two images is the mean square difference of the component value, comparing each pixel with
the pixel in the same position of the other image. For the purposes of this computation, components are normalized to the scale [0..1].
The maximum mean square difference is identically 1.
So the higher the PSNR, the closer the images are. A luminance PSNR of 20 means the mean square difference of the luminances of the pixels
is 100 times less than the maximum possible difference, i.e. 0.01.
SEE ALSO pnm(5)
04 March 2001 pnmpsnr(1)