==================================================
The network card stats
Code:
root@ABRO-DB/#netstat -v ent0
-------------------------------------------------------------
ETHERNET STATISTICS (ent0) :
Device Type: Virtual I/O Ethernet Adapter (l-lan)
Hardware Address: b2:51:b4:3b:20:0b
Elapsed Time: 88 days 4 hours 58 minutes 42 seconds
Transmit Statistics: Receive Statistics:
-------------------- -------------------
Packets: 127202332052 Packets: 98167235979
Bytes: 99027328638719 Bytes: 46966446811491
Interrupts: 0 Interrupts: 51688301615
Transmit Errors: 0 Receive Errors: 0
Packets Dropped: 0 Packets Dropped: 0
Bad Packets: 0
Max Packets on S/W Transmit Queue: 0
S/W Transmit Queue Overflow: 0
Current S/W+H/W Transmit Queue Length: 0
Broadcast Packets: 18288 Broadcast Packets: 92360313
Multicast Packets: 4 Multicast Packets: 0
No Carrier Sense: 0 CRC Errors: 0
DMA Underrun: 0 DMA Overrun: 0
Lost CTS Errors: 0 Alignment Errors: 0
Max Collision Errors: 0 No Resource Errors: 0
Late Collision Errors: 0 Receive Collision Errors: 0
Deferred: 0 Packet Too Short Errors: 0
SQE Test: 0 Packet Too Long Errors: 0
Timeout Errors: 0 Packets Discarded by Adapter: 0
Single Collision Count: 0 Receiver Start Count: 0
Multiple Collision Count: 0
Current HW Transmit Queue Length: 0
General Statistics:
-------------------
No mbuf Errors: 0
Adapter Reset Count: 0
Adapter Data Rate: 20000
Driver Flags: Up Broadcast Running
Simplex 64BitSupport ChecksumOffload
DataRateSet VIOENT
Virtual I/O Ethernet Adapter (l-lan) Specific Statistics:
---------------------------------------------------------
RQ Length: 9025
Trunk Adapter: False
Filter MCast Mode: False
Filters: 255
Enabled: 2 Queued: 0 Overflow: 0
LAN State: Operational
Hypervisor Send Failures: 0
Receiver Failures: 0
Send Errors: 0
Hypervisor Receive Failures: 0
Invalid VLAN ID Packets: 0
ILLAN Attributes: 000000000000B002 [000000000000A000]
Port VLAN ID: 140
VLAN Tag IDs: None
Switch ID: ETHERNET0
Hypervisor Information
Virtual Memory
Total (KB) 150
I/O Memory
VRM Minimum (KB) 172
VRM Desired (KB) 172
DMA Max Min (KB) 256
Transmit Information
Transmit Buffers
Buffer Size 65536
Buffers 32
History
No Buffers 7
Virtual Memory
Total (KB) 2048
I/O Memory
VRM Minimum (KB) 2176
VRM Desired (KB) 16384
DMA Max Min (KB) 16384
Receive Information
Receive Buffers
Buffer Type Tiny Small Medium Large Huge
Min Buffers 2048 2048 256 64 64
Max Buffers 4096 4096 512 128 128
Allocated 2048 2063 271 64 64
Registered 2047 2040 254 64 64
History
Max Allocated 2048 2280 362 74 64
Lowest Registered 2046 2033 251 59 64
Virtual Memory
Minimum (KB) 1024 4096 4096 2048 4096
Maximum (KB) 2048 8192 8192 4096 8192
I/O Memory
VRM Minimum (KB) 16384 16384 5120 2304 4352
VRM Desired (KB) 32768 32768 10240 4608 8704
DMA Max Min (KB) 32768 32768 16384 8192 16384
I/O Memory Information
Total VRM Minimum (KB) 46892
Total VRM Desired (KB) 105644
Total DMA Max Min (KB) 123136
Moderator's Comments:
To keep the forums high quality for all users, please take the time to format your posts correctly. The moderators are getting tired of reformatting every post you submit.
First of all, use Code Tags when you post any code or data samples so others can easily read your code. You can easily do this by highlighting your code and then clicking on the # in the editing menu. (You can also type code tags [code] and [/code] by hand.)
Note that CODE tags are used for full-line and multi-line sample input, sample output, and code segments, and ICODE tags are only used for partial-line sample input, sample output, and code segments.
Last edited by rbatte1; 01-05-2017 at 06:40 AM..
Reason: Don Cragun: Change ICODE tags to CODE tags and add ICODE tags.; rbatte1: Joined lines in output for clarity
Hello everybody.
I have a problem with my AIX 5.3. Recently my unix shows a high cpu utilization with sar or topas.
I need to find what I have to do to solve this problem, in fact, I don't know what is my problem.
I had the same problem with another AIX 5.3 running the same... (2 Replies)
About 4 years ago I wrote this tool inspired by Rob Urban's collect tool for DEC's Tru64 Unix. What makes this tool as different as collect was in its day is its ability to run at a low overhead and collect tons of stuff. I've expanded the general concept and even include data not available in... (0 Replies)
Hello Friends,
On one of my Solaris 10 box, CPU usage shows 100% using "sar", "vmstat". However, it has 4 CPUs and prstat and glance are not showing enough processes to justify high CPU utilization.
=========================================================================
$ prstat -a
... (4 Replies)
Hi All,
While creating zone we will mention min and max cpu cores, like
add dedicated-cpu
set ncpus=NUM_CPUS_MIN-NUM_CPUS_MAX
end
Ques1:
Suppose thing that non global zone uses only minimum cores at particular time What the other cores will do, Will it shared to global zone?
Ques:2... (1 Reply)
There might be some problem with my server,
because every morning at 7, it's performance become bad with no DB extra deadlock.
But I just couldn't figure it out.
Please give me some advise, thanks a lot...
According to the CPU performace chart, Daily CPU loading Maximum: 42 %, Average:36%.
... (8 Replies)
hi
We have migrated SCO 5.0.6 into ESX4, but the VM eats 100% of the virtual CPU.
Here is top print from the SCO VM:
last pid: 16773; load averages: 1.68, 1.25, 0.98 02:08:41
79 processes: 75 sleeping, 2 running, 1 zombie, 1 onproc
CPU states: 0.0% idle, 17.0% user,... (7 Replies)
We have a DB server which is constantly utilised above 95% above.
This is becoming nuisance when the monitoring team frequently calls to check on it. Frankly I do not know what to tweak or even interpret the outputs.
I noticed constant 30 to 60% in wio column of the cpu utilisation.
There... (1 Reply)
I want to write a shell script which will print AIX
CPU utilization
memory utilization
every 5 mins redirect to file. How do i do it? Please advise.
Which commands I should use? (3 Replies)
Hi all,
Been reading a lot of the cpu load and its "analogy of it to car traffic path of expressway"
From wiki
Most UNIX systems count only processes in the running (on CPU) or runnable (waiting for CPU) states. However, Linux also includes processes in uninterruptible sleep states... (13 Replies)
01-05-2017
