11-01-2016
You haven't added the Broadcom device yet? Is this because you tried, and the device is not either of the ones for which there is a SCO driver.
HP does not have any SCO drivers for the z400.
For the Realtek card you probably have to supply the PCI Slot number, the Bus Number and the Device Number. These are sometimes available in the CMOS, or are displayed during POST.
This User Gave Thanks to jgt For This Post:
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Our shops server runs SCO Openserver 5 release 5. It has two network cards in it (one on 10.0.0.6 and one on 90.0.0.99). When I run scoadmin and look at the network settings it show both my 3com network cards and a loop back driver http://theentertainer.com/james/untitled.jpg
Can anyone tell... (1 Reply)
Discussion started by: potter
1 Replies
2. SCO
I have got a Sco Unix Server, i want to connect some windows workstations. What configurations do i need to make on server and or workstation? (1 Reply)
Discussion started by: tpurazi1
1 Replies
3. AIX
I have an LPAR in a P5 machine which has been setup in an HACMP cluster. The person who set it up allocated the wrong network adapter (en) to the persistent network. For the life of me I cannot find where I can re-assign this adapter. Anyone able to help me as I am tearing my hair out and do not... (1 Reply)
Discussion started by: johnf
1 Replies
4. SCO
Hello Guys,
We have an old PC running on SCO Unix V. Is there any sites where i can get manual/procedures on how to install and configure Network. Thanks (2 Replies)
Discussion started by: nrcuevas
2 Replies
5. AIX
hello
i've need to change network adapter on machine H80 aix 4.3.3 hacmp ( ent0 )
what i need to do after the new adapter installed on the machine?
thanks
best regards
ariec (1 Reply)
Discussion started by: ariec
1 Replies
6. AIX
When I configure two VIO Servers, VIOS1 used to ping its gateway, after I configured second VIOS2, VIOS1 cannpt ping its gateway, when I run this command:
entstat -all ent#|grep -i priority
Priority: 5 Active: False
How to make Active to True? (1 Reply)
Discussion started by: rainbow_bean
1 Replies
7. UNIX for Dummies Questions & Answers
Hi All,
I am new here - this is my first post.
I have installed Solaris 10 5/09 on my Dell M6300. The install went well, but the Dell's onboard network card is the Broadcom BCM5756ME Gigabit Ethernet - and sadly no Solaris driver exists for it. The Solaris 10 install just jumped by the... (1 Reply)
Discussion started by: soulmerchant
1 Replies
8. UNIX for Dummies Questions & Answers
Hi All
I P2Vd a Unixware 7.1.4 box with VMWare Vsphere. I try to add a network adapter under Network Configuration Manager and it comes up with the error attached.
I've added a virtual adapter using the "E1000" option. It detects both the AMD PCI NET and E1000 virtual adapters under Network... (8 Replies)
Discussion started by: flashinwrx
8 Replies
9. SCO
hi
i installed sco unix open server 5.0.7 on virtual machine vmware and runing it,
its work perfect and good.
now how i can configuare network at scoadmin that i able to access nework ?
---------- Post updated at 08:56 AM ---------- Previous update was at 01:47 AM ----------
nobody can... (2 Replies)
Discussion started by: farzad226
2 Replies
10. Red Hat
Hello community, I have a Proliant HP DL380P with the following network adapters:
NetXtreme BCM5719 Gigabit Ethernet PCIe (Ethernet 1Gb 4-port 331FLR Adapter)
82580 Gigabit Network Connection (NC365T 4-port Ethernet Server Adapter)
I installed Red Hat 7.2 but it recognizes only the... (9 Replies)
Discussion started by: Lord Spectre
9 Replies
BWI(4) BSD Kernel Interfaces Manual BWI(4)
NAME
bwi -- Broadcom BCM43xx IEEE 802.11b/g wireless network driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device bwi
device wlan
device wlan_amrr
device firmware
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_bwi_load="YES"
DESCRIPTION
The bwi driver provides support for Broadcom BCM43xx based PCI/CardBus network adapters.
It supports station and monitor mode operation. Only one virtual interface may be configured at any time. For more information on configur-
ing this device, see ifconfig(8).
This driver requires firmware to be loaded before it will work. The ports/net/bwi-firmware-kmod port needs to be installed before
ifconfig(8) will work.
HARDWARE
The bwi driver supports Broadcom BCM43xx based wireless devices, including:
Card Chip Bus Standard
Apple Airport Extreme BCM4306 PCI b/g
Apple Airport Extreme BCM4318 PCI b/g
ASUS WL-138g BCM4318 PCI b/g
Buffalo WLI-CB-G54S BCM4318 CardBus b/g
Buffalo WLI-PCI-G54S BCM4306 PCI b/g
Compaq R4035 onboard BCM4306 PCI b/g
Dell Wireless 1470 BCM4318 Mini PCI b/g
Dell Truemobile 1400 BCM4309 Mini PCI b/g
HP nx6125 BCM4319 PCI b/g
Linksys WPC54G Ver 3 BCM4318 CardBus b/g
Linksys WPC54GS Ver 2 BCM4318 CardBus b/g
TRENDnet TEW-401PCplus BCM4306 CardBus b/g
US Robotics 5411 BCM4318 CardBus b/g
EXAMPLES
Join an existing BSS network (i.e., connect to an access point):
ifconfig wlan create wlandev bwi0 inet 192.168.0.20
netmask 0xffffff00
Join a specific BSS network with network name ``my_net'':
ifconfig wlan create wlandev bwi0 ssid my_net up
Join a specific BSS network with 64-bit WEP encryption:
ifconfig wlan create wlandev bwi0 ssid my_net
wepmode on wepkey 0x1234567890 weptxkey 1 up
SEE ALSO
arp(4), cardbus(4), intro(4), pci(4), wlan(4), wlan_amrr(4), ifconfig(8), wpa_supplicant(8)
HISTORY
The bwi driver first appeared in FreeBSD 8.0.
AUTHORS
The bwi driver was written for DragonFly BSD by Sepherosa Ziehau and subsequently ported to FreeBSD.
BUGS
Some card based on the BCM4306 and BCM4309 chips do not work properly on channel 1, 2 and 3.
BSD
May 16, 2009 BSD