10-31-2016
What steps did you take after installing all that software?
Some possibilities:
The nic is disabled in the CMOS.
netconfig requires that you input the PCI parameters, and you have left them at the default 0,0,0.
The nic is defective.
This User Gave Thanks to jgt For This Post:
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Our shops server runs SCO Openserver 5 release 5. It has two network cards in it (one on 10.0.0.6 and one on 90.0.0.99). When I run scoadmin and look at the network settings it show both my 3com network cards and a loop back driver http://theentertainer.com/james/untitled.jpg
Can anyone tell... (1 Reply)
Discussion started by: potter
1 Replies
2. SCO
I have got a Sco Unix Server, i want to connect some windows workstations. What configurations do i need to make on server and or workstation? (1 Reply)
Discussion started by: tpurazi1
1 Replies
3. AIX
I have an LPAR in a P5 machine which has been setup in an HACMP cluster. The person who set it up allocated the wrong network adapter (en) to the persistent network. For the life of me I cannot find where I can re-assign this adapter. Anyone able to help me as I am tearing my hair out and do not... (1 Reply)
Discussion started by: johnf
1 Replies
4. SCO
Hello Guys,
We have an old PC running on SCO Unix V. Is there any sites where i can get manual/procedures on how to install and configure Network. Thanks (2 Replies)
Discussion started by: nrcuevas
2 Replies
5. AIX
hello
i've need to change network adapter on machine H80 aix 4.3.3 hacmp ( ent0 )
what i need to do after the new adapter installed on the machine?
thanks
best regards
ariec (1 Reply)
Discussion started by: ariec
1 Replies
6. AIX
When I configure two VIO Servers, VIOS1 used to ping its gateway, after I configured second VIOS2, VIOS1 cannpt ping its gateway, when I run this command:
entstat -all ent#|grep -i priority
Priority: 5 Active: False
How to make Active to True? (1 Reply)
Discussion started by: rainbow_bean
1 Replies
7. UNIX for Dummies Questions & Answers
Hi All,
I am new here - this is my first post.
I have installed Solaris 10 5/09 on my Dell M6300. The install went well, but the Dell's onboard network card is the Broadcom BCM5756ME Gigabit Ethernet - and sadly no Solaris driver exists for it. The Solaris 10 install just jumped by the... (1 Reply)
Discussion started by: soulmerchant
1 Replies
8. UNIX for Dummies Questions & Answers
Hi All
I P2Vd a Unixware 7.1.4 box with VMWare Vsphere. I try to add a network adapter under Network Configuration Manager and it comes up with the error attached.
I've added a virtual adapter using the "E1000" option. It detects both the AMD PCI NET and E1000 virtual adapters under Network... (8 Replies)
Discussion started by: flashinwrx
8 Replies
9. SCO
hi
i installed sco unix open server 5.0.7 on virtual machine vmware and runing it,
its work perfect and good.
now how i can configuare network at scoadmin that i able to access nework ?
---------- Post updated at 08:56 AM ---------- Previous update was at 01:47 AM ----------
nobody can... (2 Replies)
Discussion started by: farzad226
2 Replies
10. Red Hat
Hello community, I have a Proliant HP DL380P with the following network adapters:
NetXtreme BCM5719 Gigabit Ethernet PCIe (Ethernet 1Gb 4-port 331FLR Adapter)
82580 Gigabit Network Connection (NC365T 4-port Ethernet Server Adapter)
I installed Red Hat 7.2 but it recognizes only the... (9 Replies)
Discussion started by: Lord Spectre
9 Replies
LEARN ABOUT HPUX
pci_eh_enable
pci_eh_enable(5) File Formats Manual pci_eh_enable(5)
NAME
pci_eh_enable - enables/disables PCI Error Recovery
VALUES
Failsafe
Default
(Enables PCI Error Recovery.)
Allowed values
Integer values from to
Recommended values
(Enables PCI Error Recovery.)
DESCRIPTION
HP-UX supports PCI Error Handling/Recovery to ensure that PCI errors caused by bad cards do not crash a hard partition on high end systems.
This functionality helps in recovering the most common parity errors. This tunable is made static because it is very hard to modify hard-
ware capability at run time.
is made public so certain service guard users would be able to turn off the functionality.
Who Is Expected to Change This Tunable?
Recommended for service guard customers.
Restrictions on Changing
Changes to this tunable take effect at next reboot.
When Should the Tunable Be Turned On?
This tunable should be turned on to enable PCI Error Recovery functionality
When Should the Tunable Be Turned Off?
To disable PCI Error Recovery functionality
What Are the Side Effects of Turning the Tunable Off?
PCI Error Recovery functionality will be disabled
WARNINGS
Even if tunable is PCI Error Handling/Recovery functionality will be disabled if the platform does not have the capability.
All HP-UX kernel tunable parameters are release specific. This parameter may be removed or have its meaning changed in future releases of
HP-UX.
Installation of optional kernel software, from HP or other vendors, may cause changes to tunable parameter values. After installation,
some tunable parameters may no longer be at the default or recommended values. For information about the effects of installation on tun-
able values, consult the documentation for the kernel software being installed. For information about optional kernel software that was
factory installed on your system, see at
AUTHOR
was developed by HP.
Kernel Tunable for PCI Error Recovery pci_eh_enable(5)