I’m familiar with load balancing.. but Is it possible to actually bond multiple DSL lines together? I hear of ways to bond using MLPPP but that requires support from an ISP. Is there a way to actually bond without support from my ISP, or use say a cable modem and a DSL line together for faster... (0 Replies)
Hello.
Our Company is spreaded over Germany.
There are main offices an branch offices.
These offices are mostly connecte via multiple sdsl.
We build a IPSEC VPN Infrastructure using Aastaro Security Gateways appliances.
It seemed that only one VPN Connetion between to offices could be... (0 Replies)
I need to enable Ethernet Bonding on three systems, connected together via switch. What I tried ended up with failure, slaves cannot be detected n added to bon0.
Here's what I did:
created file /etc/modprobe.d/bonding.d and added the following to it:
alias bond0 bonding
options bonding... (2 Replies)
I am new to linux. I have a falconstor CDP installation which runs on RHEL 5.5 (Tikanga). There is a vendor option to bond nics in either 802.3ad or round robin, I choose 802.3ad. The server is connected to a Cisco 3750 switch.
The problem is dropped packets and eth03 wont come up in the PO... (0 Replies)
Does anyone know if it's possible to bond two bonds together? My situation is I have two older Cisco switches that cannot carry a LACP (bond level 4) aggregated between them, but separate aggregates can be setup on the switches themselves. In order to have redundancy of two switches I would... (0 Replies)
Hi team,
I'm running into a problem configuring bonding on an CentOS 64bit on DELL Server. I'm connecting eth0 and eth1
to a Cisco 2948 (CatOS 8.1(3)) and receiving flapping notices. The
ethernet address is that of the primary interface. I have tried
several different modes,... (3 Replies)
HI all,
First post on the forum, and my first proper project on the Paspberry Pi, so sorry if this is in the wrong place.
I am trying to turn my Pi in to a 3G/4G Bonding router. I have been researching and trying this for a week or so now. The basic plan is to have up to 6 ZTE MF823 USB... (0 Replies)
I have one production system where my customized application runs.The applications require seamless network connectivity with different machines connected in LAN and WAN. As these applications are very critical, it is very much required to have a seamless network activity.The applications are... (4 Replies)
bond0 active in eth0 and inactive in eth4. why eth4 received network package?
Bonding Mode: fault-tolerance (active-backup)
Primary Slave: eth0 (primary_reselect failure)
Currently Active Slave: eth0
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 0
Down Delay (ms): 0
... (4 Replies)
Discussion started by: samran35
4 Replies
LEARN ABOUT CENTOS
smpppd-ifcfg
SMPPPD-IFCFG(8) SMPPPD SMPPPD-IFCFG(8)NAME
smpppd-ifcfg - SuSE Meta PPP Daemon
DESCRIPTION
smpppd-ifcfg is a daemon that controls a single dialup connection to the internet. It does so by starting and controlling the pppd. The
configuration of the dialup connections is done by YaST2.
smpppd-ifcfg is not intended for direct use. Use ifup and ifdown or a frontend like cinternet , qinternet or kinternet instead.
OPTIONS
These options are recognized by smpppd-ifcfg. If a long option shows an argument as mandatory, then it is mandatory for the equivalent
short option also.
--up Bring the connection up. This is the default action.
--down Bring the connection down.
--status
Report status of the connection.
-i, --ifcfg=NAME
Specify the ifcfg file to use. This option is mandatory.
-p, --provider=NAME
Specify the provider file to use.
--detach
Detach from the controlling terminal. This is the default.
--nodeatch
Don't detach from the controlling terminal.
-d, --debug
Turn on debugging.
--version
Show program version and exit.
--help Show help information and exit.
FILES
/etc/sysconfig/network/ifcfg-*
Configuration files for the interfaces.
/etc/sysconfig/network/providers/*
Configuration files for the providers.
/var/log/smpppd/ifcfg-xxx.log
Log file.
/var/log/smpppd/accounting.log
File containing accounting information.
/var/run/smpppd.ifcfg-xxx.pid
Pid file.
/var/lib/smpppd/ifcfg-xxx.info
Info file with various status information.
/var/run/smpppd/ifcfg-xxx
Socket to communicate with smpppd.
SEE ALSO
kinternet, qinternet, cinternet(1), accounting(1), wvdial(1), smpppd.conf(5), pppd(8), smpppd(8).
AUTHOR
Arvin Schnell <arvin@suse.de>
SuSE December 2002 SMPPPD-IFCFG(8)