I have found in the httpd.conf where it it states the default parse pages like index.htm, index.html, index.php and etc....However, my computer box does not seem to want to automatically load the index.php files. Anyone have any ideas? (5 Replies)
Have been asked to remove all images from being logged to the access_log ... where am I going wrong?<VirtualHost 123.456.789.99>
ServerName www.somedomain.com.au
DocumentRoot /agents/tts
Redirect /wap http://somewap.com.au/traveler
LogFormat "%v %h %l %u %t \"%r\" %>s %b" comonvhost... (2 Replies)
I have just configured httpd.conf on a new Redhat 9 install. Below are my additions to httpd.conf. Everything works fine except that when typing http://spetnik.d2g.com into my web browser, I am sent to the "Default catch all" site. Any clues?
NameVirtualHost *:80
#Default catch all ... (5 Replies)
Hi everybody,
I have installed Apache 2 + Tomcat 5.5. on Ubuntu 7.04 and the default httpd.conf is empty (0 lines), however there is a file called apache2.conf that looks like a default httpd.conf.
I didn't use Apache in ages, since 1.3.x release, but I remember that the httpd.conf by default... (2 Replies)
Hi ,
Need to add a following line to many webserver configuration .
ie. Need to make following entry in "LimitRequestLine 4000" in httpd.conf.
Any ideas welcome
Regards,
logic0 (2 Replies)
I'd like to know if servername in apache httpd.conf is the machine name or domain name. If it is domain name like example.com, should it be registered before in use? (1 Reply)
Hi, I was wondering if someone could help me out here. I am super-paranoid, so am trying to limit what PHP files can be executed on this server. I have a small list of files that I want to allow. The rest, deny. So I have base rule that denies all php files server-wide: order allow,deny ... (0 Replies)
Hi, I was wondering if someone could help me out here. I am super-paranoid, so am trying to limit what PHP files can be executed on this server. I have a small list of files that I want to allow. The rest, deny:
<Files ~ "\.(php|php3)$">
order allow,deny
deny from all
</Files>
I... (0 Replies)
Hello Guys !!
wanted to use SED to pull cout the full vertualhost entry for domain which is specified from command line
Like (IP base httpd.conf)
domain="ServerName takemewithyou.in"
sed -n '/<VirtualHost* $domain/,/<\/VirtualHost>/p' httpd.conf
File can take to test is below
... (0 Replies)
Discussion started by: SilvesterJ
0 Replies
LEARN ABOUT MINIX
chmem
CHMEM(1) General Commands Manual CHMEM(1)NAME
chmem - change memory allocation
SYNOPSIS
chmem [+] [-] [=] amount file
EXAMPLES
chmem =50000 a.out # Give a.out 50K of stack space
chmem -4000 a.out # Reduce the stack space by 4000 bytes
chmem +1000 file1 # Increase each stack by 1000 bytes
DESCRIPTION
When a program is loaded into memory, it is allocated enough memory for the text and data+bss segments, plus an area for the stack. Data
segment growth using malloc , brk , or sbrk eats up stack space from the low end. The amount of stack space to allocate is derived from a
field in the executable program's file header. If the combined stack and data segment growth exceeds the stack space allocated, the pro-
gram will be terminated.
It is therefore important to set the amount of stack space carefully. If too little is provided, the program may crash. If too much is
provided, memory will be wasted, and fewer programs will be able to fit in memory and run simultaneously. MINIX does not swap, so that
when memory is full, subsequent attempts to fork will fail. The compiler sets the stack space to the largest possible value (for the Intel
CPUs, 64K - text - data). For many programs, this value is far too large. Nonrecursive programs that do not call brk , sbrk , or malloc ,
and do not have any local arrays usually do not need more than 8K of stack space.
The chmem command changes the value of the header field that determines the stack allocation, and thus indirectly the total memory required
to run the program. The = option sets the stack size to a specific value; the + and - options increment and decrement the current value by
the indicated amount. The old and new stack sizes are printed.
SEE ALSO install(1), brk(2).
CHMEM(1)