to split the flar file into its component parts, one of which will be a cpio archive.
Copying the flar file somewhere else and splitting it will at least enable you to check what (cpio) archive exists and that it does contain what you expected.
Hello,
I am new to AIX, as I was primarily working on HP-UX servers.
We have some production servers and a couple of lab servers. We have upgraded over 40 servers from 5.2 to 5.3 running a particular application(1) using the golden 5.3 upgraded servers copy of makesysb. We have only two... (3 Replies)
Hello All,
I backed up my RHEL 4 as an image.
Then I restored the image on my machine. Everything went fine but I dont get the normal boot sequence as it used to come when I freshly installed RHEL4.
The messages that are shown when the system boots are something like-
" .....
EXT3-fs:... (2 Replies)
I have a T2000 server that is JumpStarted with Solaris 10 from the JumpStart server. Host name and IP address is changed after that. Then we backup the server using FLAR to tape:
root.damas# date; flarcreate -c -t -n "Sol10_cairo_image" -a "engineering@starsolutions.com" -R / /dev/rmt/0n ;... (2 Replies)
In a Solaris9 environment I'm trying to restore flash archive (flar) with SVM mirrored devices to same server via jumpstart server and it is failing to create boot file and drops down to a command prompt in single user mode, metastat -i and metastat -p output looks good when compared to the ones... (0 Replies)
Hi,
can someone help with the following?
I got 1x146GB disk which is span by just one zfs rpool.
When issue for example:
as you can see in above output the flar is very small, just around 10KB
rpool with all data sets has several GB so this can't be good image. This is on the Solaris 10... (3 Replies)
I'm new to utilizing Solaris... especially the old 8 version, but I'm trying to find out if there is a way to create a Flash Archive of a disk that can be restored on a smaller size disk or disk of varying size? (2 Replies)
Dear Team:
I am new to this Forum and I need your help for my AIX restoration problem
its very urgent
my problem as follow
failure I have a Tivoli Storage Manger was installed on that server.
I created backup image using Tivoli and it created a set of files each file is around 2GB
so... (1 Reply)
Hi Folks,
How to restore mksysb image on LPAR which is already having cloned AIX OS installed on hdisk0 (nothing configured, only full partition image is sitting on hdisk0)
Let me know.
Thank a lot. (1 Reply)
Hi Folks,
I know that we can install the flar image inside solaris non-global or branded zones.
But can we install flar image in the global zone?
If yes, then how?
My use case is, while preparing setups, every time i needs to install Solaris OS (say sol10) on the machine and have to install... (1 Reply)
I want to migrate a solaris 10 os to solaris 11.4 zone.
I did this
a)Collect some data like id sysid,disks,ip,etc..on solaris10
OK
b)Create this file.cfg with this command on solaris 10
zonep2vchk -c > /migration/sol10.cfg
OK
c)Create the archive flash on Solaris10 (1 Reply)
Discussion started by: Linusolaradm1
1 Replies
LEARN ABOUT OPENSOLARIS
root_archive
root_archive(1M) System Administration Commands root_archive(1M)NAME
root_archive - manage bootable miniroot archives
SYNOPSIS
/boot/solaris/bin/root_archive pack archive root
/boot/solaris/bin/root_archive unpack archive root
/boot/solaris/bin/root_archive packmedia solaris_image root
/boot/solaris/bin/root_archive unpackmedia solaris_image root
DESCRIPTION
The root_archive utility is used to manage bootable miniroot archives and is currently only available on x86 platforms. The utility can
pack and unpack boot/root archives in both ufs and hsfs (iso9660) format. It will always generate ufs archives.
root_archive also uses the lofi file driver to export a file as a block device (see lofi(7D)) and mount to mount or unmount file systems
and remote resources (see mount(1M)). root_archive requires the same privileges that are needed to run these commands.
SUBCOMMANDS
The root_archive command has the following subcommands:
pack archive root Pack from the image found under the root directory to the archive.
unpack archive root
Unpack from the archive to an unpacked image under the root directory.
packmedia solaris_image root
Pack the solaris image to the root directory.
unpackmedia solaris_image root
Unpack the solaris image from the root directory.
For packmedia and unpackmedia, other items that do not go into the ramdisk image are copied or uncopied (see cpio(1)) as well. Specifi-
cally, this includes all the packaging databases needed for pkgadd and the other packaging utilities to succeed which are not used in the
running and hence pruned to conserve memory.
EXAMPLES
Example 1 Unpacking the Solaris x86 install image
The following command unpacks the current Solaris image from the root directory:
# root_archive unpackmedia
/export/nv/solarisdvd.nvx_dvd/latest /export/Boot
Where /export/nv/solarisdvd.nvx_dvd/latest represents a path to a Solaris x86 install image and /export/Boot is a directory that will be
purged or created, as necessary.
Example 2 Packing the Solaris x86 install image
The following command packs the current Solaris image to the root directory:
# root_archive packmedia
/export/nv/solarisdvd.nvx_dvd/latest /export/Boot
EXIT STATUS
The following exit values are returned:
0 The command completed successfully.
1 The command exited due to an error.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
|Interface Stability |Stable |
+-----------------------------+-----------------------------+
SEE ALSO cpio(1), bootadm(1M), mount(1M), attributes(5), lofi(7D)SunOS 5.11 26 Sep 2005 root_archive(1M)