|
|
Sponsored Content
Operating Systems
AIX
Is it possible to configure bonding over bonded interface in AIX?
Post 302975831 by dukessd on Sunday 19th of June 2016 08:10:50 PM
|
|
10 More Discussions You Might Find Interesting
1. Red Hat
Netdump over bonded interface ?
Hey there,..
I have heard from admins, that netdump usually fails over a bonded network interface.
I have written a multi-OS checkdump script , which checks if the respective crashdump utility on corresponding OS is correctly configured, space is available,... (1 Reply)
Discussion started by: shriyer
1 Replies
2. Red Hat
Hi
I have installed OEL 4 on my dell XPS laptop. But when i connect the LAN cable and try to acesss internet. it does not work. the led's in the port do not blink when i plug in the cable .do i need some drivers please suggest.
Thanks
Ankur (2 Replies)
Discussion started by: ankurk
2 Replies
3. AIX
Hi,
I am totally new to AIX. I would like to know how to create virtual interface on AIX machine.
Thanks,
Pooja (4 Replies)
Discussion started by: pooja84k
4 Replies
4. Red Hat
Hi All,
I need to configure a floating IP on loopback interface of two servers (RHEL 5.4). After configuring, I'm not able to ping to that IP from a different server.
I fail to understand what is missing here. I have done similar configuration in another environment & it works fine.
Plz help.... (0 Replies)
Discussion started by: max_min
0 Replies
5. IP Networking
Hello,
I've been using mode 4 with four slaves, however looking at ifconfig showed that the traffic was not balanced correctly between the interfaces, the outgoing traffic has been alot higher on the last slave.
Example:
eth0 RX 123.2 GiB TX 22.5 GiB
eth1 RX 84.8 GiB TX 8.3 GiB
eth2... (3 Replies)
Discussion started by: TehOne
3 Replies
6. Solaris
Hi,
I have installed Solaris 10 on VMware7, When i used ifconfig -a to check network interface, it has shown lo0 as loopback interface.
Please advise how to configure network interfaces using VMware. (1 Reply)
Discussion started by: ajhal04
1 Replies
7. IP Networking
Hello,
I am trying to set up Channel Bonding on a RHEL6 Virtual Box VM. I have 2 ethernet cards on the machine which are set up in Internal Network mode. I followed all the steps exactly as mentioned in the RHEL6 deployment Guide, but for some reason i think results are not correct. Here are my... (13 Replies)
Discussion started by: Rohit Bhanot
13 Replies
8. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
9. IP Networking
HI all,
First post on the forum, and my first proper project on the Paspberry Pi, so sorry if this is in the wrong place.
I am trying to turn my Pi in to a 3G/4G Bonding router. I have been researching and trying this for a week or so now. The basic plan is to have up to 6 ZTE MF823 USB... (0 Replies)
Discussion started by: elliottlc
0 Replies
10. UNIX for Dummies Questions & Answers
Hi,
I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output. Below are few files and command output for your... (1 Reply)
Discussion started by: omkar.jadhav
1 Replies
LEARN ABOUT OPENSOLARIS
ath
ath(7D) Devices ath(7D) NAME
ath - Atheros AR52xx 802.11b/g wireless NIC driver DESCRIPTION
The ath 802.11b/g wireless NIC driver is a multi-threaded, loadable, clonable, GLDv3-based STREAMS driver for the Atheros AR52xx (AR5210/5211/5212) chipset-based wireless NIC. The ath driver functions include controller initialization, wireless 802.11b/g infrastructure network connection, WEP, frame transmit and receive, and promiscuous and multi-cast support. DRIVER CONFIGURATION
The ath driver performs auto-negotiation to determine the data rates and mode. Supported 802.11b data rates (Mbits/sec.) are 1, 2, 5.5 and 11. Supported 802.11g data rates (Mbits/sec.) are 1, 2, 5.5, 11, 6, 9, 12, 18, 24, 36, 48 and 54. The ath driver supports only BSS networks (also known as "ap" or "infrastructure" networks) and the "open" (or "opensystem") authentica- tion type. Only WEP encryption is currently supported. Configuration and administration can be performed through the dladm(1M) or wificonfig(1M) utilities. FILES
/dev/ath* Special character device. /kernel/drv/ath 32-bit ELF kernel module (x86). /kernel/drv/amd64/ath 64-bit ELF kernel module (x86). ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Architecture |x86 | +-----------------------------+-----------------------------+ SEE ALSO
dladm(1M), wificonfig(1M), gld(7D) ANSI/IEEE Std 802.11- Standard for Wireless LAN Technology, 1999. IEEE Std 802.11a- Standard for Wireless LAN Technology-Rev. A, 2003 IEEE Std 802.11b - Standard for Wireless LAN Technology-Rev.B, 2003 IEEE Std 802.11g-- Standard for Wireless LAN Technology - Rev. G, 2003 SunOS 5.11 14 Nov 2006 ath(7D)