Is it possible to configure bonding over bonded interface in AIX? Post: 302975831

10 More Discussions You Might Find Interesting

1. Red Hat

Netdump over bonded interface ?

Netdump over bonded interface ? Hey there,.. I have heard from admins, that netdump usually fails over a bonded network interface. I have written a multi-OS checkdump script , which checks if the respective crashdump utility on corresponding OS is correctly configured, space is available,...

2. Red Hat

How to configure network interface card in OEL.

Hi I have installed OEL 4 on my dell XPS laptop. But when i connect the LAN cable and try to acesss internet. it does not work. the led's in the port do not blink when i plug in the cable .do i need some drivers please suggest. Thanks Ankur

3. AIX

Virtual interface on AIX

Hi, I am totally new to AIX. I would like to know how to create virtual interface on AIX machine. Thanks, Pooja

4. Red Hat

Configure floating IP on loopback interface

Hi All, I need to configure a floating IP on loopback interface of two servers (RHEL 5.4). After configuring, I'm not able to ping to that IP from a different server. I fail to understand what is missing here. I have done similar configuration in another environment & it works fine. Plz help....

5. IP Networking

Interface bonding / Link aggregation (Multiple)

Hello, I've been using mode 4 with four slaves, however looking at ifconfig showed that the traffic was not balanced correctly between the interfaces, the outgoing traffic has been alot higher on the last slave. Example: eth0 RX 123.2 GiB TX 22.5 GiB eth1 RX 84.8 GiB TX 8.3 GiB eth2...

6. Solaris

Configure network interface for Solaris 10

Hi, I have installed Solaris 10 on VMware7, When i used ifconfig -a to check network interface, it has shown lo0 as loopback interface. Please advise how to configure network interfaces using VMware.

7. IP Networking

Channel bonding Issue - Bond0 interface not getting up in on RHEL6

Hello, I am trying to set up Channel Bonding on a RHEL6 Virtual Box VM. I have 2 ethernet cards on the machine which are set up in Internal Network mode. I followed all the steps exactly as mentioned in the RHEL6 deployment Guide, but for some reason i think results are not correct. Here are my...

8. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without...

9. IP Networking

Is bond0 ready and a bonding interface? - 4G Bonding Router Problems (RPI)

HI all, First post on the forum, and my first proper project on the Paspberry Pi, so sorry if this is in the wrong place. I am trying to turn my Pi in to a 3G/4G Bonding router. I have been researching and trying this for a week or so now. The basic plan is to have up to 6 ZTE MF823 USB...

10. UNIX for Dummies Questions & Answers

Assigning ipv6 to bonding interface - getting old as well as changed ipv6 in ifconfig output

Hi, I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output. Below are few files and command output for your...

LEARN ABOUT OPENSOLARIS

pcwl

pcwl(7D)							      Devices								  pcwl(7D)

NAME

       pcwl - Lucent/PrismII 802.11b wireless NIC driver

DESCRIPTION

       The   pcwl   802.11b  wireless  NIC driver is a multi- threaded, loadable, clonable, GLDv3-based STREAMS driver. It supports the pccard and
       PCI/MiniPCI cards with the Lucent and PrismII 802.11b chipsets on x86 and SPARC.

DRIVER CONFIGURATION

       The pcwl driver supports 802.11b data rates of 1, 2, 5.5 and 11 (Mbits/sec). The default is 11.

       The pcwl driver supports BSS networks (also known as "ap" or "infrastructure" networks) and IBSS (or "ad-hoc") networks. For authentication
       type,  the  pcwl  driver  supports the "open" (or "open-system") mode and the "shared-key" mode. For encryption type, only WEP is currently
       supported. You perform configuration and administration tasks using the dladm(1M) and wificonfig(1M) utilities.

FILES

       /dev/pcwl*		   Special character device.

       /kernel/drv/pcwl 	   32-bit ELF kernel module (x86).

       /kernel/drv/amd64/pcwl	   64-bit ELF kernel module (x86).

       /kernel/drv/sparcv9/pcwl    64-bit ELF kernel module (SPARC).

ATTRIBUTES

       See attributes(5) for a description of the following attributes:

       +-----------------------------+-----------------------------+
       |      ATTRIBUTE TYPE	     |	    ATTRIBUTE VALUE	   |
       +-----------------------------+-----------------------------+
       |Availability		     |SPARC, x86		   |
       +-----------------------------+-----------------------------+

SEE ALSO

       dladm(1M), wificonfig(1M), attributes(5), gld(7D)

       802.11b Standard for Wireless Local Area Networks (WLANs) - IEEE

SunOS 5.11							    24 Jan 2007 							  pcwl(7D)

10 More Discussions You Might Find Interesting

1. Red Hat

Netdump over bonded interface ?

Discussion started by: shriyer

2. Red Hat

How to configure network interface card in OEL.

Discussion started by: ankurk

3. AIX

Virtual interface on AIX

Discussion started by: pooja84k

4. Red Hat

Configure floating IP on loopback interface

Discussion started by: max_min