06-19-2016
What do you think?
Did you try?
What happened?
Are ent4 and 5 NIB or 802.3ad?
What do you want to know - we need details.............
This User Gave Thanks to dukessd For This Post:
10 More Discussions You Might Find Interesting
1. Red Hat
Netdump over bonded interface ?
Hey there,..
I have heard from admins, that netdump usually fails over a bonded network interface.
I have written a multi-OS checkdump script , which checks if the respective crashdump utility on corresponding OS is correctly configured, space is available,... (1 Reply)
Discussion started by: shriyer
1 Replies
2. Red Hat
Hi
I have installed OEL 4 on my dell XPS laptop. But when i connect the LAN cable and try to acesss internet. it does not work. the led's in the port do not blink when i plug in the cable .do i need some drivers please suggest.
Thanks
Ankur (2 Replies)
Discussion started by: ankurk
2 Replies
3. AIX
Hi,
I am totally new to AIX. I would like to know how to create virtual interface on AIX machine.
Thanks,
Pooja (4 Replies)
Discussion started by: pooja84k
4 Replies
4. Red Hat
Hi All,
I need to configure a floating IP on loopback interface of two servers (RHEL 5.4). After configuring, I'm not able to ping to that IP from a different server.
I fail to understand what is missing here. I have done similar configuration in another environment & it works fine.
Plz help.... (0 Replies)
Discussion started by: max_min
0 Replies
5. IP Networking
Hello,
I've been using mode 4 with four slaves, however looking at ifconfig showed that the traffic was not balanced correctly between the interfaces, the outgoing traffic has been alot higher on the last slave.
Example:
eth0 RX 123.2 GiB TX 22.5 GiB
eth1 RX 84.8 GiB TX 8.3 GiB
eth2... (3 Replies)
Discussion started by: TehOne
3 Replies
6. Solaris
Hi,
I have installed Solaris 10 on VMware7, When i used ifconfig -a to check network interface, it has shown lo0 as loopback interface.
Please advise how to configure network interfaces using VMware. (1 Reply)
Discussion started by: ajhal04
1 Replies
7. IP Networking
Hello,
I am trying to set up Channel Bonding on a RHEL6 Virtual Box VM. I have 2 ethernet cards on the machine which are set up in Internal Network mode. I followed all the steps exactly as mentioned in the RHEL6 deployment Guide, but for some reason i think results are not correct. Here are my... (13 Replies)
Discussion started by: Rohit Bhanot
13 Replies
8. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
9. IP Networking
HI all,
First post on the forum, and my first proper project on the Paspberry Pi, so sorry if this is in the wrong place.
I am trying to turn my Pi in to a 3G/4G Bonding router. I have been researching and trying this for a week or so now. The basic plan is to have up to 6 ZTE MF823 USB... (0 Replies)
Discussion started by: elliottlc
0 Replies
10. UNIX for Dummies Questions & Answers
Hi,
I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output. Below are few files and command output for your... (1 Reply)
Discussion started by: omkar.jadhav
1 Replies
LEARN ABOUT OPENSOLARIS
network-admin
network-admin(1) User Commands network-admin(1)
NAME
network-admin - Basic administration of network interfaces.
SYNOPSIS
network-admin [--configure=INTERFACE] [--configure-type=TYPE] [gnome-std-options]
DESCRIPTION
network-admin enumerates the interfaces available to the user and provides a mechanism for configuring these interfaces as static-IP or
DHCP. It's also possible to select which interfaces should be enabled on boot.
network-admin also allows you configure the systems hostname, DNS options and hosts using the user interface.
OPTIONS
The following options are supported:
-c, --configure=INTERFACE Configure a specific network interface (e.g. ath0 or bge0).
-t, --configure-type=TYPE Configure the first network interface of a specific type (e.g. ethernet or wireless).
gnome-std-options Standard options available for use with most GNOME applications. See gnome-std-options(5) for more informa-
tion.
EXAMPLES
Example 1: Running the main application.
example% network-admin
Example 2: Configuring the ath0 network interface.
example% network-admin --configure=ath0
Example 3: Configuring the first ethernet interface.
example% network-admin --configure-type=ethernet
EXIT STATUS
The following exit values are returned:
0 Application exited successfully
>0 Application exited with failure
FILES
The following files are used by this application:
/usr/bin/network-admin Executable for network interface configuration.
/etc/inet/gnome-system-tools Storage location for network configuration files when not active on boot.
/var/spool/setup-tool-backends/backup/network
Backup directory for files that are modified.
/var/spool/setup-tool-backends/data/network
Where "Location" profiles are stored.
/var/run/setup-tool-backends/debug/network
Debug logs can be found under here.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWgnome-system-tools |
+-----------------------------+-----------------------------+
|Interface stability |Uncommitted |
+-----------------------------+-----------------------------+
SEE ALSO
Latest version of the GNOME Desktop User Guide for your platform.
users-admin(1), shares-admin(1), services-admin(1), time-admin(1), gnome-std-options(5), ifconfig(1M), hosts(4), nsswitch.conf(4),
resolv.conf(4), attributes(5)
NOTES
This tool can only be used to manage physical network devices as returned by the "dladm show-dev" command, it does not support configura-
tion of more complex configurations.
There is currently no support for enterprise name services such as YP/NIS, NIS+ or LDAP. There is also no support for anything but the
global zone.
Written by Darren Kenny, Sun Microsystems Inc., 2006.
SunOS 5.11 6 Nov 2006 network-admin(1)