06-19-2016
Is it possible to configure bonding over bonded interface in AIX?
Hi Everyone,
Is it possible to configure bonding over bonded interface in AIX?
For example:
server has for NIC port:
ent0
ent1
ent2
ent3
First I create a EtherChannel ent4 from ent0 and ent1.
and then I create a EtherChannel ent5 from ent2 and ent3.
Can I create a EtherChannel ent6 from ent4 and ent5?
10 More Discussions You Might Find Interesting
1. Red Hat
Netdump over bonded interface ?
Hey there,..
I have heard from admins, that netdump usually fails over a bonded network interface.
I have written a multi-OS checkdump script , which checks if the respective crashdump utility on corresponding OS is correctly configured, space is available,... (1 Reply)
Discussion started by: shriyer
1 Replies
2. Red Hat
Hi
I have installed OEL 4 on my dell XPS laptop. But when i connect the LAN cable and try to acesss internet. it does not work. the led's in the port do not blink when i plug in the cable .do i need some drivers please suggest.
Thanks
Ankur (2 Replies)
Discussion started by: ankurk
2 Replies
3. AIX
Hi,
I am totally new to AIX. I would like to know how to create virtual interface on AIX machine.
Thanks,
Pooja (4 Replies)
Discussion started by: pooja84k
4 Replies
4. Red Hat
Hi All,
I need to configure a floating IP on loopback interface of two servers (RHEL 5.4). After configuring, I'm not able to ping to that IP from a different server.
I fail to understand what is missing here. I have done similar configuration in another environment & it works fine.
Plz help.... (0 Replies)
Discussion started by: max_min
0 Replies
5. IP Networking
Hello,
I've been using mode 4 with four slaves, however looking at ifconfig showed that the traffic was not balanced correctly between the interfaces, the outgoing traffic has been alot higher on the last slave.
Example:
eth0 RX 123.2 GiB TX 22.5 GiB
eth1 RX 84.8 GiB TX 8.3 GiB
eth2... (3 Replies)
Discussion started by: TehOne
3 Replies
6. Solaris
Hi,
I have installed Solaris 10 on VMware7, When i used ifconfig -a to check network interface, it has shown lo0 as loopback interface.
Please advise how to configure network interfaces using VMware. (1 Reply)
Discussion started by: ajhal04
1 Replies
7. IP Networking
Hello,
I am trying to set up Channel Bonding on a RHEL6 Virtual Box VM. I have 2 ethernet cards on the machine which are set up in Internal Network mode. I followed all the steps exactly as mentioned in the RHEL6 deployment Guide, but for some reason i think results are not correct. Here are my... (13 Replies)
Discussion started by: Rohit Bhanot
13 Replies
8. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
9. IP Networking
HI all,
First post on the forum, and my first proper project on the Paspberry Pi, so sorry if this is in the wrong place.
I am trying to turn my Pi in to a 3G/4G Bonding router. I have been researching and trying this for a week or so now. The basic plan is to have up to 6 ZTE MF823 USB... (0 Replies)
Discussion started by: elliottlc
0 Replies
10. UNIX for Dummies Questions & Answers
Hi,
I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output. Below are few files and command output for your... (1 Reply)
Discussion started by: omkar.jadhav
1 Replies
LEARN ABOUT DEBIAN
ifenslave-2.6
IFENSLAVE(8) BSD System Manager's Manual IFENSLAVE(8)
NAME
ifenslave -- Attach and detach slave network devices to a bonding device.
SYNOPSIS
ifenslave [-acdfhuvV] [--all-interfaces] [--change-active] [--detach] [--force] [--help] [--usage] [--verbose] [--version] master slave ...
DESCRIPTION
ifenslave is a tool to attach and detach slave network devices to a bonding device. A bonding device will act like a normal Ethernet network
device to the kernel, but will send out the packets via the slave devices using a simple round-robin scheduler. This allows for simple load-
balancing, identical to "channel bonding" or "trunking" techniques used in switches.
The kernel must have support for bonding devices for ifenslave to be useful.
OPTIONS
-a, --all-interfaces
Show information about all interfaces.
-c, --change-active
Change active slave.
-d, --detach
Removes slave interfaces from the bonding device.
-f, --force
Force actions to be taken if one of the specified interfaces appears not to belong to an Ethernet device.
-h, --help
Display a help message and exit.
-u, --usage
Show usage information and exit.
-v, --verbose
Print warning and debug messages.
-V, --version
Show version information and exit.
If not options are given, the default action will be to enslave interfaces.
EXAMPLE
The following example shows how to setup a bonding device and enslave two real Ethernet devices to it:
# modprobe bonding
# ifconfig bond0 192.168.0.1 netmask 255.255.0.0
# ifenslave bond0 eth0 eth1
AUTHOR
ifenslave was originally written by Donald Becker <becker@cesdis.gsfc.nasa.gov>, and has since been updated by various kernel developers.
This manual page was written by Guus Sliepen <guus@debian.org> for the Debian GNU/Linux system.
Debian GNU/Linux June 1, 2019 Debian GNU/Linux