In you sample file02.out sample, the 3rd line is:
Is that correct, or did you intend to have:
Are you looking for a match on any substring of the 2nd field in file02.out, or are you looking for an exact match on the first three components of the IP address in the 2nd field in file02.out?
What operating system and shell are you using?
Thanks for spotting that error, I corrected it. I intended to have as per your example. I am looking for an exact match on the first three components on the second field.
I'm having problems since few days ago, and i'm not able to make it works with a simple awk+grep script (or other way to do this).
For example, i have a input file1.txt:
cat inputfile1.txt
218299910417
1172051195
1172070231
1172073514
1183135117
1183135118
1183135119
1281440202
... (3 Replies)
Friends,
File1.txt
abc|0|xyz
123|129|opq
def|0|678
890|pqw|sdf
How do I print the entire line where second column has value is 0?
Expected Result:
abc|0|xyz
def|0|678
Thanks,
Prashant
---------- Post updated at 02:14 PM ---------- Previous update was at 02:06 PM ----------
... (1 Reply)
Hi Experts,
I am very new to scripting and have a prb since few days and it is urgent to solve so much appreciated if u help me.
i have 2 files
file1.txt
9647810043118
9647810043126
9647810043155
9647810043161
9647810043166
9647810043185
9647810043200
9647810043203
9647810043250... (22 Replies)
Hi,
My input files is like this
axis1 0 1 10
axis2 0 1 5
axis1 1 2 -4
axis2 2 3 -3
axis1 3 4 5
axis2 3 4 -1
axis1 4 5 -6
axis2 4 5 1
Now, these are my following tasks
1. Print a first column for every two rows that has the same value followed by a string.
2. Match on the... (3 Replies)
Hello Everyone,
I have a file with 5 fields in each line just like mentioned below. Also the 4th field is time elapsed(hh:mm:ss) since the process is running
xyz abc status 23:00:00 idle
abc def status 24:00:00 idle
def gji status 27:00:02 idle
fgh gty status 00:00:00 idle
Here I... (8 Replies)
I have one requirement to delete all lines from a file if it matches below scenario. File contains three column. Employee Number, Employee Name and Employee ID
Scenario is: delete all line if Employee Number (1st column) contains below
1. Non-numeric Employee Number
2. Employee Number that... (3 Replies)
Hi,
I have some data like below:
John 254
Chris 254
Matt 123
Abe 123
Raj 487
Moh 487
How can i print it using awk to have:
254 John,Chris
123 Matt,Abe
487 Raj,Moh
Thanks. (4 Replies)
I cannot seem to get what should be a simple awk one-liner to work correctly and cannot figure out why. I would like to use patterns from a specific field in one file as regex to search for matching strings in the entire line ($0) of another file.
I would like to output the lines of File2 which... (1 Reply)
hi
I have 2 file with more than 10 columns for both
1st file
apple,0,0,0......
orange,1,2,3.....
mango,2,4,5.....
2nd file
apple,2,3,4,5,6,7...
orange,2,3,4,5,6,8...
watermerlon,2,3,4,5,6,abc...
mango,5,6,7,4,6,def.... (1 Reply)
Discussion started by: tententen
1 Replies
LEARN ABOUT FREEBSD
if_gre
GRE(4) BSD Kernel Interfaces Manual GRE(4)NAME
gre -- encapsulating network device
SYNOPSIS
To compile the driver into the kernel, place the following line in the kernel configuration file:
device gre
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_gre_load="YES"
DESCRIPTION
The gre network interface pseudo device encapsulates datagrams into IP. These encapsulated datagrams are routed to a destination host, where
they are decapsulated and further routed to their final destination. The ``tunnel'' appears to the inner datagrams as one hop.
gre interfaces are dynamically created and destroyed with the ifconfig(8) create and destroy subcommands.
This driver corresponds to RFC 2784. Encapsulated datagrams are prepended an outer datagram and a GRE header. The GRE header specifies the
type of the encapsulated datagram and thus allows for tunneling other protocols than IP. GRE mode is also the default tunnel mode on Cisco
routers. gre also supports Cisco WCCP protocol, both version 1 and version 2.
The gre interfaces support a number of additional parameters to the ifconfig(8):
grekey Set the GRE key used for outgoing packets. A value of 0 disables the key option.
enable_csum Enables checksum calculation for outgoing packets.
enable_seq Enables use of sequence number field in the GRE header for outgoing packets.
EXAMPLES
192.168.1.* --- Router A -------tunnel-------- Router B --- 192.168.2.*
/
/
+------ the Internet ------+
Assuming router A has the (external) IP address A and the internal address 192.168.1.1, while router B has external address B and internal
address 192.168.2.1, the following commands will configure the tunnel:
On router A:
ifconfig greN create
ifconfig greN inet 192.168.1.1 192.168.2.1
ifconfig greN inet tunnel A B
route add -net 192.168.2 -netmask 255.255.255.0 192.168.2.1
On router B:
ifconfig greN create
ifconfig greN inet 192.168.2.1 192.168.1.1
ifconfig greN inet tunnel B A
route add -net 192.168.1 -netmask 255.255.255.0 192.168.1.1
NOTES
The MTU of gre interfaces is set to 1476 by default, to match the value used by Cisco routers. This may not be an optimal value, depending
on the link between the two tunnel endpoints. It can be adjusted via ifconfig(8).
For correct operation, the gre device needs a route to the decapsulating host that does not run over the tunnel, as this would be a loop.
The kernel must be set to forward datagrams by setting the net.inet.ip.forwarding sysctl(8) variable to non-zero.
SEE ALSO gif(4), inet(4), ip(4), me(4), netintro(4), protocols(5), ifconfig(8), sysctl(8)
A description of GRE encapsulation can be found in RFC 2784 and RFC 2890.
AUTHORS
Andrey V. Elsukov <ae@FreeBSD.org>
Heiko W.Rupp <hwr@pilhuhn.de>
BUGS
The current implementation uses the key only for outgoing packets. Incoming packets with a different key or without a key will be treated as
if they would belong to this interface.
The sequence number field also used only for outgoing packets.
BSD November 7, 2014 BSD