Hi all,
I'm stuck on this last part...am running a simple script under AIX to extract NetView host IP addresses. The line below returns the IP address in parenthesis with a trailing colon, i.e.
ping -c 1 $name |grep \( | awk '{ print $3 }' --------> returns
(a.b.c.d):
How can I only... (10 Replies)
Hallo all,
I have a script which creates an output ... see below:
root@a7germ:/tmp/pax > cat 20061117.txt
523.047
521.273
521.034
517.367
516.553
517.793
513.114
513.940
I would like to use awk to calculate the (a)total sum of the numbers (b) The average of the numbers.
Please... (4 Replies)
Dear All
How are you
I have files which look like this :
20080406_12:43:55.779 ISC Sprint- 39 21624032999 218925866728
20080406_12:44:07.811 ISC Sprint- 20 21620241815 218927736810
20080406_12:44:00.485 ISC Sprint- 50 21621910404 218913568053... (0 Replies)
Hello, i'm unable to remove the parenthesis character.
With $parsed_AsciiName =~ s/\(//;
the string is the same
And with $parsed_AsciiName =~ s/(//;
i retrieve "Unmatched ( in regex; marked by <-- HERE in m/( <-- HERE"
Any ideas, please? thank you in advanced. (4 Replies)
I have a list of coordinate data, sampled below.
54555209 784672723
I want it as:
545552.09 7846727.23
Below is my script:
BEGIN {FS= " "; OFS= ","} {print $1*.01,$2*.01}
This is my outcome:
5.5e7 7.8e8
How do I tell awk that I want to keep all the digits instead of outputting... (1 Reply)
hi there again,
i need to do a simple division with my data with a number of rows. i think i wanted to have a simple output like this one:
col1 col2 col3
val1 val2 val1/val2
valn valm valn/valm
any suggestion is very much appreciated. thanks much. (2 Replies)
I created a awk state to calculate the number of success however when the query runs it has a leading zero. Any ideas on how to remove the leading zero from the calculation?
Here is my query:
cat myfile.log | grep | awk '{print $2,$3,$7,$11,$15,$19,$23,$27,$31,$35($19/$15*100)}'
02:00:00... (1 Reply)
Hi,
I have files in a folder that I would like all renamed without the preceding number and parenthesis. For example, I have files of the name
08) Great Good Fine Ok - Not Going Home
09) Roosevelt - Small Hours
10) RAC - I Should've Guessed Feat. SPEAK
and I would like them all to be... (4 Replies)
I am trying to run the awk below. My question is when I split the input, then run anotherawk to perform a calculation using that splitas the input there are no issues. When I try to combine them the output is not correct, is the split not working or did I do it wrong? Thank you :).
input
... (8 Replies)
In the below awk, I am trying to calculate percent for a given id. It is very close the problem is when the # being used in the calculation is zero. I am not sure how to code this condition into the awk as it happens frequently. The portion in italics was an attempt but that lead to an error. Thank... (13 Replies)
Discussion started by: cmccabe
13 Replies
LEARN ABOUT CENTOS
sfddiff
SFDDIFF(1) General Commands Manual SFDDIFF(1)NAME
sfddiff - compare two font files
SYNOPSIS
sfddiff [--help] [--ignorehints] [--ignorenames] [--ignoregpos] [--ignoregsub] [--ignorebitmaps] [--exact] [--warn] [--merge outfile]
[--usage] [--version] fontfile1 fontfile2
DESCRIPTION
The program sfddiff compares two font files, which may be in any format fontforge(1) can read. It will notice the following differences:
1) Characters are present in one font but not in the other.
2) Characters are present in both fonts but have different sets of outlines or references. The outlines may be compared so that only
exact matches are accepted, or so that a fuzzier match is used. Similarly references may need to match exactly, or may be matched
after an unlink.
This fuzzy comparison is useful when comparing truetype and postscript fonts, or when comparing a font with references to one with-
out.
3) The postscript hints or truetype instructions are different.
4) The font names (the truetype `name' table) differ.
5) The kerning (and other `gpos' information) differs.
6) The ligatures (and other `gsub' information) differ.
7) Any bitmap strikes present in one font but not in the other.
8) Any bitmap characters present in one strike of one font but in the equivalent strike of the other.
9) Any bitmap characters which differ.
OPTIONS --help Provide a description with a list of the available options.
--ignorehints
Suppress the reporting of hint/instruction differences.
--ignoregpos
Suppress the reporting of kerning (and other `gpos') differences.
--ignoregsub
Suppress the reporting of ligature (and other `gsub') differences.
--ignorenames
Suppress the reporting of name string differences.
--ignorebitmaps
Suppress the reporting of bitmap differences.
--exact
Require outlines to match exactly.
--warn Warn if the outlines/references are slightly different.
--merge outfile
Store a merged version of the two fonts into the specified output file. The merged data will be based on sfdfile1, as well as any
characters present in sfdfile2 but not in sfdfile1 will be added, and the outlines of sfdfile2 will be placed in the background.
Finally, for any characters with different outlines or references the background of the character will contain the outlines from
sfdfile2 (references will be unlinked into outlines and those outlines also will be added).
--usage
Display the usage description.
--version
Display the current version.
SEE ALSO fontforge(1)
The HTML version of the fontforge manual at:
http://fontforge.sourceforge.net/
AUTHOR
Copyright (C) 2000-2006 by George Williams (gww@silcom.com). Manual page heavily rewritten and modified to use standard -man(5) macros by
R.P.C. Rodgers (rodgers@nlm.nih.gov), 23 October 2002.
8 April 2006 SFDDIFF(1)
06-02-2016
