The awk below works fine if I manually remove the () from file1. However, when I try to use tr to remove the () and then | into awk to run the calculation no result is obtained. Is there a way to tell the awk to ignore the () in fiile1 if they are there or do I need to remove them first? Thank you .
Hi all,
I'm stuck on this last part...am running a simple script under AIX to extract NetView host IP addresses. The line below returns the IP address in parenthesis with a trailing colon, i.e.
ping -c 1 $name |grep \( | awk '{ print $3 }' --------> returns
(a.b.c.d):
How can I only... (10 Replies)
Hallo all,
I have a script which creates an output ... see below:
root@a7germ:/tmp/pax > cat 20061117.txt
523.047
521.273
521.034
517.367
516.553
517.793
513.114
513.940
I would like to use awk to calculate the (a)total sum of the numbers (b) The average of the numbers.
Please... (4 Replies)
Dear All
How are you
I have files which look like this :
20080406_12:43:55.779 ISC Sprint- 39 21624032999 218925866728
20080406_12:44:07.811 ISC Sprint- 20 21620241815 218927736810
20080406_12:44:00.485 ISC Sprint- 50 21621910404 218913568053... (0 Replies)
Hello, i'm unable to remove the parenthesis character.
With $parsed_AsciiName =~ s/\(//;
the string is the same
And with $parsed_AsciiName =~ s/(//;
i retrieve "Unmatched ( in regex; marked by <-- HERE in m/( <-- HERE"
Any ideas, please? thank you in advanced. (4 Replies)
I have a list of coordinate data, sampled below.
54555209 784672723
I want it as:
545552.09 7846727.23
Below is my script:
BEGIN {FS= " "; OFS= ","} {print $1*.01,$2*.01}
This is my outcome:
5.5e7 7.8e8
How do I tell awk that I want to keep all the digits instead of outputting... (1 Reply)
hi there again,
i need to do a simple division with my data with a number of rows. i think i wanted to have a simple output like this one:
col1 col2 col3
val1 val2 val1/val2
valn valm valn/valm
any suggestion is very much appreciated. thanks much. (2 Replies)
I created a awk state to calculate the number of success however when the query runs it has a leading zero. Any ideas on how to remove the leading zero from the calculation?
Here is my query:
cat myfile.log | grep | awk '{print $2,$3,$7,$11,$15,$19,$23,$27,$31,$35($19/$15*100)}'
02:00:00... (1 Reply)
Hi,
I have files in a folder that I would like all renamed without the preceding number and parenthesis. For example, I have files of the name
08) Great Good Fine Ok - Not Going Home
09) Roosevelt - Small Hours
10) RAC - I Should've Guessed Feat. SPEAK
and I would like them all to be... (4 Replies)
I am trying to run the awk below. My question is when I split the input, then run anotherawk to perform a calculation using that splitas the input there are no issues. When I try to combine them the output is not correct, is the split not working or did I do it wrong? Thank you :).
input
... (8 Replies)
In the below awk, I am trying to calculate percent for a given id. It is very close the problem is when the # being used in the calculation is zero. I am not sure how to code this condition into the awk as it happens frequently. The portion in italics was an attempt but that lead to an error. Thank... (13 Replies)
Discussion started by: cmccabe
13 Replies
LEARN ABOUT LINUX
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)