06-01-2016
Just wanted to understand this, is it safe to say that the second subnet starts after the broadcast address:
192.168.0.0 /22
255.255.252.0
192.168.0.0 – 192.168.(3).255(Broadcast address)
192.168.(4).0 – 192.168.(7).255(Broadcast address), then next subnet
192.168.(8).0 – 192.168.(11).255(Broadcast address), then next subnet
192.168.(12).0 – 192.168.(15).255(Broadcast address)
And so on...
Similarly for the below IP:
IP Address – 172.59.0.0
Custom Subnet Mask – 255.255.252.0
Broadcast Address – 172.59.3.255
172.59.0.0 - 172.59.3.255
172.59.4.0 - 172.59.7.255
172.59.8.0 - 172.59.11.255
172.59.12.0 - 172.59.15.255
And so on....
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Before I even attempt this, is it possible to grep for a pattern, maybe a partial sentence like "go to page 3", assign that to a variable and then use awk or something to pull out the 3 and assign it to a variable? So first I would have
Gotopg = "go to page 3"
then
page = 3 (9 Replies)
Discussion started by: k@ssidy
9 Replies
2. Shell Programming and Scripting
Hi
In my shell script, I'm trying to find the line count of a file and assign it to a variable.
LINE_COUNT=$(wc -l $FILE_NAME)
But when i display LINE_COUNT, i'm getting the linecount concatenated with the file name. I want only the number. How can i get the line count alone ? Someone... (2 Replies)
Discussion started by: janemary.a
2 Replies
3. HP-UX
hi all,
i want to know where i can add and IP address so when i do a "w", i can see what IP is assigned to which tty? i know in tru64 you just added an entry to /etc/hosts. this does not seem to be the case with hpux.
thanks (12 Replies)
Discussion started by: macgre_r
12 Replies
4. Shell Programming and Scripting
hi all,
in ksh, how do i assign the output of a find command to a variable, e.g
am trying something like this :
totalNoFiles=$(print find ./ -name "SystemOut*.log");
but when i echo $totalNoFiles it displays
find ./ -name "SystemOut*.log"
instead of the total number of... (2 Replies)
Discussion started by: cesarNZ
2 Replies
5. Shell Programming and Scripting
can we make a global variable and store character values and add other values to that variable ?? for example
a="hello, John"
and can we add value ". How are you? so
a can have
"hello, John. How are you?"
can someone help me?? (2 Replies)
Discussion started by: bonosungho
2 Replies
6. Shell Programming and Scripting
I want to print between the range two patterns if a particular pattern is present in between the two patterns. I am new to Unix. Any help would be greatly appreciated.
e.g.
Pattern1
Bombay
Calcutta
Delhi
Pattern2
Pattern1
Patna
Madras
Gwalior
Delhi
Pattern2
Pattern1... (2 Replies)
Discussion started by: joyan321
2 Replies
7. AIX
Hi admins
i want to assign new ip adress to my aix 5.3 machine which is in LPAR
ent3 Available Virtual I/O Ethernet Adapter (l-lan)
ent0 Available 05-08 2-Port 10/100/1000 Base-TX PCI-X Adapter (14108902)
ent1 Available 05-09 2-Port 10/100/1000 Base-TX PCI-X Adapter (14108902)
ent2... (0 Replies)
Discussion started by: newaix
0 Replies
8. Shell Programming and Scripting
Unable to get the value to a variable.
set -x
cd $HOME
echo "Enter the server name"
read a
echo $a
i=4
j=1
k = ps -ef | awk '/server1/{ print $4 }' | tail -$i | head -$j`
echo $k
When I do the same in command line it works, however the same does not work when I provide that in the... (1 Reply)
Discussion started by: venkidhadha
1 Replies
9. IP Networking
Hi All,
I'm a bit confused about assigning IP address from IP Ranges.
I am using this scenario below to understand.
Scenario
Adatum.com an international IT solutions company, is launching 12 new branches in a new country where they currently have no existing branches. The sWin CIO has asked... (3 Replies)
Discussion started by: TryllZ
3 Replies
10. Shell Programming and Scripting
Hi,
I couldn't find any thing on google about it and have been trying to figure this out but am not getting anywhere. I want to know if its possible through a script. I have a file with columns start time and end time separated by a comma, basically there are some other columns which I need to... (30 Replies)
Discussion started by: dsid
30 Replies
LEARN ABOUT FREEBSD
if_gre
GRE(4) BSD Kernel Interfaces Manual GRE(4)
NAME
gre -- encapsulating network device
SYNOPSIS
To compile the driver into the kernel, place the following line in the kernel configuration file:
device gre
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_gre_load="YES"
DESCRIPTION
The gre network interface pseudo device encapsulates datagrams into IP. These encapsulated datagrams are routed to a destination host, where
they are decapsulated and further routed to their final destination. The ``tunnel'' appears to the inner datagrams as one hop.
gre interfaces are dynamically created and destroyed with the ifconfig(8) create and destroy subcommands.
This driver corresponds to RFC 2784. Encapsulated datagrams are prepended an outer datagram and a GRE header. The GRE header specifies the
type of the encapsulated datagram and thus allows for tunneling other protocols than IP. GRE mode is also the default tunnel mode on Cisco
routers. gre also supports Cisco WCCP protocol, both version 1 and version 2.
The gre interfaces support a number of additional parameters to the ifconfig(8):
grekey Set the GRE key used for outgoing packets. A value of 0 disables the key option.
enable_csum Enables checksum calculation for outgoing packets.
enable_seq Enables use of sequence number field in the GRE header for outgoing packets.
EXAMPLES
192.168.1.* --- Router A -------tunnel-------- Router B --- 192.168.2.*
/
/
+------ the Internet ------+
Assuming router A has the (external) IP address A and the internal address 192.168.1.1, while router B has external address B and internal
address 192.168.2.1, the following commands will configure the tunnel:
On router A:
ifconfig greN create
ifconfig greN inet 192.168.1.1 192.168.2.1
ifconfig greN inet tunnel A B
route add -net 192.168.2 -netmask 255.255.255.0 192.168.2.1
On router B:
ifconfig greN create
ifconfig greN inet 192.168.2.1 192.168.1.1
ifconfig greN inet tunnel B A
route add -net 192.168.1 -netmask 255.255.255.0 192.168.1.1
NOTES
The MTU of gre interfaces is set to 1476 by default, to match the value used by Cisco routers. This may not be an optimal value, depending
on the link between the two tunnel endpoints. It can be adjusted via ifconfig(8).
For correct operation, the gre device needs a route to the decapsulating host that does not run over the tunnel, as this would be a loop.
The kernel must be set to forward datagrams by setting the net.inet.ip.forwarding sysctl(8) variable to non-zero.
SEE ALSO
gif(4), inet(4), ip(4), me(4), netintro(4), protocols(5), ifconfig(8), sysctl(8)
A description of GRE encapsulation can be found in RFC 2784 and RFC 2890.
AUTHORS
Andrey V. Elsukov <ae@FreeBSD.org>
Heiko W.Rupp <hwr@pilhuhn.de>
BUGS
The current implementation uses the key only for outgoing packets. Incoming packets with a different key or without a key will be treated as
if they would belong to this interface.
The sequence number field also used only for outgoing packets.
BSD
November 7, 2014 BSD