That's all about how the 32 address bits are being distributed between network address and host address. /18 means the most significant 18 bits designate the network part, and the remaining 14 bits the host part. 192.168.0.0/18 will give you 4 subnets with 16384 (= 2^14) addresses each:
For minimum 1000 devices you'll need 10 bits to accommodate 1024 addresses, so the internal /22 netmask comes in handy (32 bit - 22 bit = 10 bit addresses in each subnet). The 16 (= 2^4; 4 = 14 - 10) sub-subnet ranges are
, the 9th of which - depending how you count them, starting from 0 or 1 - is the network address 192.168.32.0 with the broadcast address 192.168.35.255 (hopefully, as my binary calculus has become somewhat rusty).
Before I even attempt this, is it possible to grep for a pattern, maybe a partial sentence like "go to page 3", assign that to a variable and then use awk or something to pull out the 3 and assign it to a variable? So first I would have
Gotopg = "go to page 3"
then
page = 3 (9 Replies)
Hi
In my shell script, I'm trying to find the line count of a file and assign it to a variable.
LINE_COUNT=$(wc -l $FILE_NAME)
But when i display LINE_COUNT, i'm getting the linecount concatenated with the file name. I want only the number. How can i get the line count alone ? Someone... (2 Replies)
hi all,
i want to know where i can add and IP address so when i do a "w", i can see what IP is assigned to which tty? i know in tru64 you just added an entry to /etc/hosts. this does not seem to be the case with hpux.
thanks (12 Replies)
hi all,
in ksh, how do i assign the output of a find command to a variable, e.g
am trying something like this :
totalNoFiles=$(print find ./ -name "SystemOut*.log");
but when i echo $totalNoFiles it displays
find ./ -name "SystemOut*.log"
instead of the total number of... (2 Replies)
can we make a global variable and store character values and add other values to that variable ?? for example
a="hello, John"
and can we add value ". How are you? so
a can have
"hello, John. How are you?"
can someone help me?? (2 Replies)
I want to print between the range two patterns if a particular pattern is present in between the two patterns. I am new to Unix. Any help would be greatly appreciated.
e.g.
Pattern1
Bombay
Calcutta
Delhi
Pattern2
Pattern1
Patna
Madras
Gwalior
Delhi
Pattern2
Pattern1... (2 Replies)
Hi admins
i want to assign new ip adress to my aix 5.3 machine which is in LPAR
ent3 Available Virtual I/O Ethernet Adapter (l-lan)
ent0 Available 05-08 2-Port 10/100/1000 Base-TX PCI-X Adapter (14108902)
ent1 Available 05-09 2-Port 10/100/1000 Base-TX PCI-X Adapter (14108902)
ent2... (0 Replies)
Unable to get the value to a variable.
set -x
cd $HOME
echo "Enter the server name"
read a
echo $a
i=4
j=1
k = ps -ef | awk '/server1/{ print $4 }' | tail -$i | head -$j`
echo $k
When I do the same in command line it works, however the same does not work when I provide that in the... (1 Reply)
Hi All,
I'm a bit confused about assigning IP address from IP Ranges.
I am using this scenario below to understand.
Scenario
Adatum.com an international IT solutions company, is launching 12 new branches in a new country where they currently have no existing branches. The sWin CIO has asked... (3 Replies)
Hi,
I couldn't find any thing on google about it and have been trying to figure this out but am not getting anywhere. I want to know if its possible through a script. I have a file with columns start time and end time separated by a comma, basically there are some other columns which I need to... (30 Replies)
Discussion started by: dsid
30 Replies
LEARN ABOUT SUSE
tgt-setup-lun
tgt-setup-lun(8) System Manager's Manual tgt-setup-lun(8)NAME
tgt-setup-lun - creates a target, adds a device to the target and defines initiators that can connect to the target
SYNOPSIS
tgt-setup-lun -d device -n target_name [initiator_IP1 initiator_IP2 ...] [-h]
DESCRIPTION
Starts tgtd if necessary and creates a target according to the supplied target_name. The format of the target name is as follows:
iqn.2001-04.com.<hostname>-<target_name> The target name must be unique.
The script then adds the requested device to the target. If specific IP addresses are defined, it adds them to the list of allowed initia-
tors for that target. If no IP addresses is defined, it defines that the target accepts any initiator.
EXAMPLES
Create a target that uses /dev/sdb1 and allows connections only from 192.168.10.81:
tgt-setup-lun -d /dev/sdb1 -n my_target 192.168.10.81
Create a target that uses /dev/sdb1 and allows connections only from 192.168.10.81 and 192.168.10.82:
tgt-setup-lun -d /dev/sdb1 -n my_target 192.168.10.81 192.168.10.82
Create a target that uses /dev/sdb1 and allows connections from any initiator:
tgt-setup-lun -d /dev/sdb1 -n my_target
Display help:
tgt-setup-lun -h
AUTHOR
Written by Erez Zilber
REPORTING BUGS
Report bugs to <erezz@voltaire.com>.
COPYRIGHT
Copyright (C) Voltaire Ltd. 2008.
tgt-setup-lun(8)