02-09-2016
Hi,
All the IPV4 addresses are allocated, your ISP probably has some availability. If not you can contact an other ISP, you can reserve an IPV6 address as well if you require.
Regards
Gull04
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
How do I use snoop command to capture multicast packets in the network? (1 Reply)
Discussion started by: caden312
1 Replies
2. Solaris
How can I assign multicast ip address to my Sun server. I need this configuration to set up weblogic in cluster mode. This setup needs a multicast IP address where the managed servers can broadcast their heartbeats.
Thanks (0 Replies)
Discussion started by: krishan
0 Replies
3. HP-UX
On HP-UX, we want to exchange data via multicast, there happen to meet a problem: sometimes the receiver that has joined the group can not receive the multicast data, but the recvfrom call returned no error. We have reconfig the network and added the default the route, but still can not fixed it,... (0 Replies)
Discussion started by: Frank2004
0 Replies
4. HP-UX
Hi, there
On HP-UX, I want to multicast packets on two different IP network repectively.
The two NIC are configured with two different IP. The routes are added with one default and one net for each IP . The multisender programs bind their own local IP, multireceiver programs add the... (0 Replies)
Discussion started by: Frank2004
0 Replies
5. Linux
On Linux, I have configured two different IP address for two network device eth0 ,eth1 , in my program, I want to multicast differently on these two network, I know it must add route for single network and I try to config another route for second network,but it can not work correctly, how to config... (0 Replies)
Discussion started by: Frank2004
0 Replies
6. Solaris
On SUN Solaris 10, if I want to multicast packets between nodes, whether it must config the multicast IP from OS, if yes, how to do it? (0 Replies)
Discussion started by: Frank2004
0 Replies
7. UNIX for Advanced & Expert Users
hi,
i'm using fedora. and i want to install mospf and pim sm services.
i read that there is mgated daemon for mospf but i cant find it.
can u tell me where to find it? and how to install it? (0 Replies)
Discussion started by: jalil smail
0 Replies
8. Solaris
On Solaris OS, We use the following command to config the multicast address for NIC in order to process the multicast packets:
# route add 228.228.228.228 10.101.10.2
Where " 228.228.228.228 " is the multicast for specified NIC ip 10.101.10.2 .
Also use the netstat -nr, the above set could... (0 Replies)
Discussion started by: Frank2004
0 Replies
9. Programming
Hello all,
I have created a UDP multicast transmitter and receiver, first using windows. But now I need the receiver to run on Ubuntu 10.04.
The code is the following:
/************************** Receiver *************************/
// Module Name: Receiver.c
//
// Description:
// ... (0 Replies)
Discussion started by: tiny05
0 Replies
10. Red Hat
Hi Gurus,
I need to add Multicast Port = xyz
Multicast Address = 123.134.143 ( example) to my firewall rules. Can you please guide me with the lines I need to update my iptables files with. (0 Replies)
Discussion started by: rama krishna
0 Replies
LEARN ABOUT OSF1
iptunnel
iptunnel(8) System Manager's Manual iptunnel(8)
NAME
iptunnel - Creates, deletes, and displays configured tunnels
SYNOPSIS
/usr/sbin/iptunnel [operation] [args]
DESCRIPTION
The iptunnel command creates configured tunnels for sending and receiving IPV6 or IPV4 packets that are encapsulated as the payload of an
IPV4 datagram.
The iptunnel command can perform one of the following operations: Creates a tunnel interface, which you must subsequently configure by
using the ifconfig command. The syntax of the create operation is as follows:
iptunnel create [-I int-name] [v4-dest] [v4-src]
Specifies the interface unit of the tunnel to be created. This is an optional parameter. The int-name parameter has the following
form: iptx, where x is the interface unit number. By default, the interface name selected for the tunnel is iptx+1, or the value of
the interface unit number of the last tunnel created plus 1. Specifies the remote end-point to which a tunnel is to be created.
Sets the IPV4 source address in the encapsulating header. The tunnel is enabled (packets are sent/received on the tunnel) only if
v4-src is a valid address on the system. This is an optional parameter. Deletes a tunnel interface. You must disable the tunnel
before you can delete it by executing the following command: # ifconfig tunnel name down delete abort Shows the tunnel attributes
(name, tunnel end points, next hop for tunneled packets).
EXAMPLES
To create a tunnel from hobbes to calvin, enter: # iptunnel create -I ipt5 calvin ipt5 iftype 208 src 16.140.16.86 dst 16.140.16.91
To display the tunnel attributes, enter: # iptunnel show ipt5 interface ipt5 src 16.140.16.86 dst 16.140.16.91 gate 16.140.16.86 To config-
uring the tunnel to encapsulate IPv6 packets, enter: # ifconfig ipt5 ipv6 up
IPv6 packets will be sent as payloads of IPv4 datagrams from 16.140.16.86 to 16.140.16.91.
The tunnel may also be used to send IPV4 packets encapsulated within IPV4 headers as follows: # ifconfig ipt5 10.10.80.60 netmask
255.255.255.0
To verify the previous command, enter: # ifconfig ipt5 ipt5: flags=4c1<UP,RUNNING,NOARP,MULTICAST>
16.140.16.86 --> 16.140.16.91
rxmt 1000, reach time 30000, dad tries 1, mtu 1280, hops 64, token len 64
inet 10.10.80.60 netmask ffffff00 ipmtu 1280
inet6 fe80::108c:1056 To deleting the tunnel, enter: # ifconfig ipt5 down delete abort ipt5: delete inet address 10.10.80.60
10.10.80.60: aborting 0 tcp connection(s)
Then, enter: # iptunnel delete ipt5 interface ipt5 deleted
SEE ALSO
Commands: ifconfig(8).
RFC 2003, IP Encapsulation within IP, Perkins, C., October 1996
iptunnel(8)