Does any one know how to get a recursive directory listing in long format (showing owner, group, permission etc) without listing the files contained in the directories.
The following command also shows the files but I only want to see the directories.
ls -lrtR * (4 Replies)
Hi,
I need a help. I want to see all the files in the directory with the Time Stamp. I use the following command.
$ls -lt
This displays the files with time stamp, but not all the files. Only last few months, the files are displayed with timestamp, the old files are only have dates.
... (2 Replies)
I have a directory named Project.I have a control file which contains valid list of files.I would like list the files from directory Project which contains files other than listed in the control file.
Sample control file:
TEST
SEND
SFFFILE
CONTL
The directory contains followign... (15 Replies)
Hi,
I am new to perl:
I need to write perl script to list all the files present in directory and mail should be come to my inbox with all the files present in that directory.
advanced thanks for valuable inputs.
Thanks
Prakash GR (1 Reply)
How can I list the files in a directory and just show the file size, date stamp, timestamp and file name..
I've been trying to ls -lrt the directory to a file and then use the cut command but I'm not having any luck with getting the proper results.. I thought i could use the -f switch and count... (4 Replies)
Hi,
(Apologies, I'm sure I'm not the first person to raise this question but so far in my searches haven't found a good answer).
I would like to output a listing per line of filename (including full path) and 'last updated' timestamp. e.g:
Z:\dir1\file1.txt 01/02/2010 10:43... (5 Replies)
Hi
I have a requirement like below
I need to sort the files based on the timestamp in the file name and run them in sorted order and then archive all the files which are one day old to temp directory
My files looks like this
PGABOLTXML1D_201108121235.xml... (1 Reply)
I need to be able to identify files with file timestamps greater than a given timestamp.
I am using the following solution, although it appears to compare files at the "seconds" granularity and I need it at the milliseconds. When I tested my solution, it missed files that had timestamps... (3 Replies)
Hi,
I want to display the file names and the record count for the files in the 2nd column for the files created today.
i have written the below command which is listing the file names. but while piping the above command to the wc -l command
its not working for me.
ls -l... (5 Replies)
Hi All
I have a file which contains the timestamp of the log and a message and I want to implement a polling mechanism, where this log file is pooled every 2 minutes and list the errors in the file. I want to list down the errors only after the timestamp in the file is more than the current... (2 Replies)
Discussion started by: infyanurag
2 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)