Sponsored Content
Operating Systems SCO Need Help Installing Legacy System on Newer Hardware Post 302960079 by spock9458 on Tuesday 10th of November 2015 04:51:50 PM
Old 11-10-2015
OK, I understand. I will take another look at my options and maybe try different hardware. I appreciate all of your help, and I might be back again. Thanks!

---------- Post updated at 02:51 PM ---------- Previous update was at 10:37 AM ----------

I am now attempting to install Open Server 5.0.6 on a different server that is from about the same era, and I've gotten it to recognize the hard disk and begin the installation. Now I have a different, less understandable problem.

I will start by saying the CD/DVD drive is recognized in CMOS as the IDE Primary Slave device, and is selected as the first Boot device. The 5.0.6 disk is in that drive and it boots up just fine. When it gets to the part where it lists the devices, however, the drive is not listed - although my hard drive is listed. When installation begins, I get to the point when it asks where my installation files are located, so I select the IDE CD Rom from the list, and I get an error. It says that there is no controller found for the device.

If there is no controller found, how is it reading the disk to get the boot process to start? I don't understand this one, so any help will be appreciated. I know it's been a long time since I've installed this O/S, but I don't remember all of these issues before. Thanks.
 

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

tar --newer = tar --newer-mtime ?

Hi, I have the following question : As far as I know unix doesn't store file creation dates. Would that imply the following? tar -cvzf backup.tar --newer is equal to: tar -cvzf backup.tar --newer-mtime ? (1 Reply)
Discussion started by: jamesbond
1 Replies

2. UNIX for Dummies Questions & Answers

Installing FreeBSD on old system?

I've never had trouble installing freebsd or any linux/unix system on any computer i've tried to do it on. I just recently aquired a Packard Bell, 75mhz Pentium, 482 i believe. Im having difficulty installing it. I have FreeBSD 5.1 on cd and the computer wont even recognize the cd on boot, so it... (2 Replies)
Discussion started by: MadProfessor
2 Replies

3. Solaris

What command to check system hardware

What command can I run on a Solaris 8 server to check the hardware (ie number of processors, speed of processors, installed memory etc). (4 Replies)
Discussion started by: soliberus
4 Replies

4. Solaris

basic hardware & system requirements for solaris 10

hi all, i want to setup a solaris10 lab for 50 trainees. kindly let me know all the basic hardware & system requirements for the lab . with regards, Raj (5 Replies)
Discussion started by: rajp_8007
5 Replies

5. Programming

VERSYS Legacy System

I need help locating the tables that hold the demograhic data in this system on an AIX box. Does anyone know the path? (0 Replies)
Discussion started by: Chelcye
0 Replies

6. AIX

System P hardware

hello everybody, Is there any training to get deep knowledge an hands on lab with system p hardware firmware microcode upgrading etc... thanks in advance (2 Replies)
Discussion started by: Vit0_Corleone
2 Replies

7. Solaris

Manufacturer name of computer system(hardware) , processor

Hi All, Can someone let me know the method or set of commands by which i can retrive manufacturer name of computer system (hardware of machine ) and manufacturer of processor. i get below information when fired psrinfo command : psrinfo -vp The physical processor has 1 virtual processor... (6 Replies)
Discussion started by: omkar.jadhav
6 Replies

8. Red Hat

Hardware and system timing are different

-> We have 2 servers server1 and server2 server. ->server1 is master application and server2 is slave application server. ->output of server1 hardware and slave timing: # hwclock --show Thu 05 Jun 2014 05:34:08 PM SGT -0.465666 seconds # date Thu Jun 5 17:34:16 SGT 2014 # cd... (6 Replies)
Discussion started by: manjusharma128
6 Replies

9. UNIX for Advanced & Expert Users

Linux Command To Find the System Configuration And Hardware Information

Hello guys. I wanted to find the System Configuration and Hardware Information on one of my servers. Here is part of the cpu info: CPU core info: processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 44 model name : Intel(R) Xeon(R) CPU... (2 Replies)
Discussion started by: Ymir
2 Replies
installboot(1M) 														   installboot(1M)

NAME
installboot - install bootblocks in a disk partition SYNOPSIS
installboot bootblk raw-disk-device The boot(1M) program, ufsboot, is loaded from disk by the bootblock program which resides in the boot area of a disk partition. The ufs boot objects are platform-dependent, and reside in the /usr/platform/platform-name/lib/fs/ufs directory. The platform name can be found using the -i option of uname(1). The installboot utility is a SPARC only program. It is not supported on the architecture. users should use installgrub(1M) instead. bootblk The name of the bootblock code. raw-disk-device The name of the disk device onto which the bootblock code is to be installed; it must be a character device which is read- able and writable. Naming conventions for a SCSI or IPI drive are c?t?d?s? and c?d?s? for an IDE drive. Example 1: Installing UFS Boot Block To install a ufs boot block on slice 0 of target 0 on controller 1 of the platform where the command is being run, use: example# installboot /usr/platform/`uname -i`/lib/fs/ufs/bootblk /dev/rdsk/c1t0d0s0 /usr/platform/platform-name/lib/fs/ufs directory where ufs boot objects reside. /platform/platform-name/ufsboot second level program to boot from a disk or CD See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWcsu | +-----------------------------+-----------------------------+ od(1), uname(1), boot(1M), init(1M), kadb(1M), kernel(1M), monitor(1M), reboot(1M), rpc.bootparamd(1M), init.d(4), attributes(5) WARNINGS
The installboot utility fails if the bootblk or openfirmware files do not exist or if the raw disk device is not a character device. 11 Apr 2005 installboot(1M)
All times are GMT -4. The time now is 05:27 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy