Sponsored Content
Operating Systems SCO Need Help Installing Legacy System on Newer Hardware Post 302959765 by jgt on Thursday 5th of November 2015 09:33:09 PM
Old 11-05-2015
Can the cmos be configured so that the sata controller is in compatible/legacy mode.
If so it should install using the wd driver.
There is no driver for the sata controller in RAID or AHCI mode.
 

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

tar --newer = tar --newer-mtime ?

Hi, I have the following question : As far as I know unix doesn't store file creation dates. Would that imply the following? tar -cvzf backup.tar --newer is equal to: tar -cvzf backup.tar --newer-mtime ? (1 Reply)
Discussion started by: jamesbond
1 Replies

2. UNIX for Dummies Questions & Answers

Installing FreeBSD on old system?

I've never had trouble installing freebsd or any linux/unix system on any computer i've tried to do it on. I just recently aquired a Packard Bell, 75mhz Pentium, 482 i believe. Im having difficulty installing it. I have FreeBSD 5.1 on cd and the computer wont even recognize the cd on boot, so it... (2 Replies)
Discussion started by: MadProfessor
2 Replies

3. Solaris

What command to check system hardware

What command can I run on a Solaris 8 server to check the hardware (ie number of processors, speed of processors, installed memory etc). (4 Replies)
Discussion started by: soliberus
4 Replies

4. Solaris

basic hardware & system requirements for solaris 10

hi all, i want to setup a solaris10 lab for 50 trainees. kindly let me know all the basic hardware & system requirements for the lab . with regards, Raj (5 Replies)
Discussion started by: rajp_8007
5 Replies

5. Programming

VERSYS Legacy System

I need help locating the tables that hold the demograhic data in this system on an AIX box. Does anyone know the path? (0 Replies)
Discussion started by: Chelcye
0 Replies

6. AIX

System P hardware

hello everybody, Is there any training to get deep knowledge an hands on lab with system p hardware firmware microcode upgrading etc... thanks in advance (2 Replies)
Discussion started by: Vit0_Corleone
2 Replies

7. Solaris

Manufacturer name of computer system(hardware) , processor

Hi All, Can someone let me know the method or set of commands by which i can retrive manufacturer name of computer system (hardware of machine ) and manufacturer of processor. i get below information when fired psrinfo command : psrinfo -vp The physical processor has 1 virtual processor... (6 Replies)
Discussion started by: omkar.jadhav
6 Replies

8. Red Hat

Hardware and system timing are different

-> We have 2 servers server1 and server2 server. ->server1 is master application and server2 is slave application server. ->output of server1 hardware and slave timing: # hwclock --show Thu 05 Jun 2014 05:34:08 PM SGT -0.465666 seconds # date Thu Jun 5 17:34:16 SGT 2014 # cd... (6 Replies)
Discussion started by: manjusharma128
6 Replies

9. UNIX for Advanced & Expert Users

Linux Command To Find the System Configuration And Hardware Information

Hello guys. I wanted to find the System Configuration and Hardware Information on one of my servers. Here is part of the cpu info: CPU core info: processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 44 model name : Intel(R) Xeon(R) CPU... (2 Replies)
Discussion started by: Ymir
2 Replies
ICP(4)							   BSD Kernel Interfaces Manual 						    ICP(4)

NAME
icp -- ICP-Vortex and Intel Storage RAID driver SYNOPSIS
icp* at pci? dev ? function ? ld* at icp? unit ? icpsp* at icp? unit ? scsibus* at icpsp? DESCRIPTION
The icp driver provides support for the newer (post 1997) ICP-Vortex GDT and Intel Storage RAID controllers. The ld driver provides access to logical devices (disk arrays) presented by the controller. The icpsp driver provides direct access to other SCSI devices attached to the controller, such as tape or CD-ROM drives. DIAGNOSTICS
pci_mem_find: expected mem type 00000000, found 00000002 This message may be displayed during autoconfiguration if the controller's memory is mapped below 1MB in physical address space. This can be disabled either through changing a setting in the controller's BIOS utility, or changing the position of a jumper on the board. See your controller's documentation for more information. SEE ALSO
intro(4), ld(4), scsi(4) HISTORY
The icp driver first appeared in NetBSD 1.6, and was based on the FreeBSD and OpenBSD drivers of the same name. BUGS
ISA & EISA front-ends and a management interface are needed. Older PCI boards are not yet supported. BSD
April 20, 2002 BSD
All times are GMT -4. The time now is 10:09 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy