Hi there, I have a csv file with some columns comma sepated like this :
4502-17,PETER,ITA2,LEGUE,92,ME - HALF,23/05/10 15:00
4502-18,CARL,ITA2,LEGUE,96,ME - HALF,20/01/09 14:00
4502-19,OTTO,ITA2,LEGUE,97,ME - MARY,23/05/10 15:00
As you can see the column n. 7 is a timestamp column, I need... (23 Replies)
Problem: I have a lot of files, the files first line should always have 4 spaces before any text. Occasionally some of the files will miss the leading spaces and it's a problem. This is only in the first line.
So if there are 4 spaces then text, do nothing. If there are not 4 spaces, add 4... (2 Replies)
Hi,
I have a space delimited text file but I only want to change the first space to a tab and keep the rest of the spaces intact. How do I go about doing that? Thanks! (3 Replies)
I created a awk state to calculate the number of success however when the query runs it has a leading zero. Any ideas on how to remove the leading zero from the calculation?
Here is my query:
cat myfile.log | grep | awk '{print $2,$3,$7,$11,$15,$19,$23,$27,$31,$35($19/$15*100)}'
02:00:00... (1 Reply)
I am trying to use awk skip each line with a ## or # and check each line after for STB= and if that value in greater than or = to 0.8, then at the end of line the text "STRAND BIAS" is written in else "GOOD".
So in the file of 4 entries attached.
awk tried:
awk NR > "##"' "#" -F"STB="... (6 Replies)
In file1 field $18 is removed.... column header is "Otherinfo", then each line in file1 is used to search file2 for a match. When a match is found the last four strings in file2 are copied to file1.
Maybe:
cut -f1-17 file1 and then match each line to file2
file1
Chr Start End ... (6 Replies)
In the awk I have a very large tab-delimeted file that I am trying to extract the DP= value put it in $16 and add
specific text to $16 with . (dot) in $11-$15 and $18. Only the lines (there are several) that have the formating below in file
will have an empty $16. Other lines will be in a... (6 Replies)
In the awk I am trying to add :p.=? to the end of each $9 that matches the pattern NM_. The below executes andis close but I can not seem to figure out why the :p.=? repeats in the split as in the green in the current output. I have added comments as well. Thank you :).
file
... (4 Replies)
The awk below executes as expected if the id in $4 (like in f) is unique. However most of my data is like f1 where the same id can appear multiple times. I think that is the reason why the awk is not working as expected. I added a comment on the line that I can not change without causing the script... (6 Replies)
Discussion started by: cmccabe
6 Replies
LEARN ABOUT MOJAVE
locale::codes::langvar
Locale::Codes::LangVar(3pm) Perl Programmers Reference Guide Locale::Codes::LangVar(3pm)NAME
Locale::Codes::LangVar - standard codes for language variation identification
SYNOPSIS
use Locale::Codes::LangVar;
$lvar = code2langvar('acm'); # $lvar gets 'Mesopotamian Arabic'
$code = langvar2code('Mesopotamian Arabic'); # $code gets 'acm'
@codes = all_langvar_codes();
@names = all_langvar_names();
DESCRIPTION
The "Locale::Codes::LangVar" module provides access to standard codes used for identifying language variations, such as those as defined in
the IANA language registry.
Most of the routines take an optional additional argument which specifies the code set to use. If not specified, the default IANA language
registry codes will be used.
SUPPORTED CODE SETS
There are several different code sets you can use for identifying language variations. A code set may be specified using either a name, or
a constant that is automatically exported by this module.
For example, the two are equivalent:
$lvar = code2langvar('en','alpha-2');
$lvar = code2langvar('en',LOCALE_CODE_ALPHA_2);
The codesets currently supported are:
alpha
This is the set of alphanumeric codes from the IANA language registry, such as 'arevela' for Eastern Armenian.
This code set is identified with the symbol "LOCALE_LANGVAR_ALPHA".
This is the default code set.
ROUTINES
code2langvar ( CODE [,CODESET] )
langvar2code ( NAME [,CODESET] )
langvar_code2code ( CODE ,CODESET ,CODESET2 )
all_langvar_codes ( [CODESET] )
all_langvar_names ( [CODESET] )
Locale::Codes::LangVar::rename_langvar ( CODE ,NEW_NAME [,CODESET] )
Locale::Codes::LangVar::add_langvar ( CODE ,NAME [,CODESET] )
Locale::Codes::LangVar::delete_langvar ( CODE [,CODESET] )
Locale::Codes::LangVar::add_langvar_alias ( NAME ,NEW_NAME )
Locale::Codes::LangVar::delete_langvar_alias ( NAME )
Locale::Codes::LangVar::rename_langvar_code ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangVar::add_langvar_code_alias ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangVar::delete_langvar_code_alias ( CODE [,CODESET] )
These routines are all documented in the Locale::Codes::API man page.
SEE ALSO
Locale::Codes
The Locale-Codes distribution.
Locale::Codes::API
The list of functions supported by this module.
http://www.iana.org/assignments/language-subtag-registry
The IANA language subtag registry.
AUTHOR
See Locale::Codes for full author history.
Currently maintained by Sullivan Beck (sbeck@cpan.org).
COPYRIGHT
Copyright (c) 2011-2013 Sullivan Beck
This module is free software; you can redistribute it and/or modify it under the same terms as Perl itself.
perl v5.18.2 2014-01-06 Locale::Codes::LangVar(3pm)
10-30-2015
.