Sponsored Content
Operating Systems SCO Backup/RAID of HD on Old UNIX Server Post 302956650 by edfair on Thursday 1st of October 2015 03:53:59 PM
Old 10-01-2015
One of my (now ex) customers had a similar situation with his accounting software. When I finally got to a support person who knew the software it turned out that the program was tied to the system name and everything transferred across and ran with different hardware.

JGT's suggestion about EDGE has worked well for me for many years. The backup is to a hard drive first with EDGE then burn the backup file and keys to CD with another program.

You can find out how much of the file systems are used with du. Your installation is pretty much standard with a /u filesystem and an extra /u1. Didn't check on their sizes.
This User Gave Thanks to edfair For This Post:
 

9 More Discussions You Might Find Interesting

1. Filesystems, Disks and Memory

2-Ch RAID Problem in SCO Open Server

Help, if possible. In SCO Open Server with installation of two-channel RAID controller the following happens: on the channel 0 disk array is seen by an operational system, and on the channel 1 array is not seen (simultaneously). That is the operational system can not simultaneously use more than... (1 Reply)
Discussion started by: pko60
1 Replies

2. Filesystems, Disks and Memory

Adding RAID to server

Hi, I have a server that I am adding a RAID that we purchased to. The server works fine. It is running Fedora 7 and is a Dell Precision 690. When the RAID is attached, it boots up and says the following: Controller Bus #00, Device#1F, Function#02: 00 Ports No device found AHCI BIOS not... (0 Replies)
Discussion started by: user23
0 Replies

3. Red Hat

linux server with raid controller card

I am planning on building a fedora box with raid controller (database server). Is anybody done that ? also what kind of software do you need to backup and recover data. (1 Reply)
Discussion started by: amir07
1 Replies

4. UNIX for Dummies Questions & Answers

efficient raid file server

I need to put together a RAID1 file server for use by Windoze systems. I've built zillions of windows systems from components. I was a HPUX SE for a long time at HP, but have been out of the game for years. I've got an old workhorse mobo FIC PA-2013 with a 450 MHz K6 III+ I could use, but I'd... (2 Replies)
Discussion started by: pcmacd
2 Replies

5. Hardware

Hardware RAID on Sun T2000 Server

Hi All I have a Sun T2000 server. Couple of years ago I had configured and mirrored the boot drive with an other drive using hardware RAID 1 using raidctl command. Following is the hardware RAID output. root@oracledatabaseserver / $ raidctl RAID Volume RAID RAID Disk... (0 Replies)
Discussion started by: Tirmazi
0 Replies

6. Hardware

Raid 0 on database server

Hi guys. if we want to use SSD drives on a database server, can we use RAID 0 configuration because of their reliability? (3 Replies)
Discussion started by: majid.merkava
3 Replies

7. Linux

Help Setting up Linux Raid Server

I just built a home computer with 3TB hard drives I wanted to set up in a RAID 5 and load Ubuntu server onto it. The first thing I did was set up the drives in a RAID 5 using just the motherboard chipset software to do it, so a 'hardware' RAID basically. I installed Windows first to see if... (2 Replies)
Discussion started by: lorewap3
2 Replies

8. Filesystems, Disks and Memory

Help finding a Unix friendly RAID 1 backup

First time poster and a very new Unix user, so I'll just pre-apologize for stupid questions now. Does anybody know of a good RAID 1 hard drive backup that is Unix friendly? I want to avoid any hardcore programming. Can you recommend both NAS and non-NAS options? I need to do nightly backups... (31 Replies)
Discussion started by: c.wakeman
31 Replies

9. Hardware

3ware RAID server

We have a 3ware RAID server at work, and as the appointed systems administrator (by virtue of being the one with the most knowledge) I've taken on the job of maintaining it. I've installed smartmontools on it to keep an eye on the drives and run scans every day, and looking at the data from the... (0 Replies)
Discussion started by: Krendoshazin
0 Replies
FSCK_MSDOS(8)						    BSD System Manager's Manual 					     FSCK_MSDOS(8)

NAME
fsck_msdos -- DOS/Windows (FAT) filesystem consistency checker SYNOPSIS
fsck_msdos -p [-f] filesystem ... fsck_msdos [-fny] [-x snap-backup] filesystem ... DESCRIPTION
The fsck_msdos utility verifies and repairs FAT filesystems (more commonly known as DOS filesystems). The first form of fsck_msdos preens the specified filesystems. It is normally started by fsck(8) run from /etc/rc during automatic reboot, when a FAT filesystem is detected. When preening file systems, fsck_msdos will fix common inconsistencies non-interactively. If more seri- ous problems are found, fsck_msdos does not try to fix them, indicates that it was not successful, and exits. The second form of fsck_msdos checks the specified file systems and tries to repair all detected inconsistencies, requesting confirmation before making any changes. The options are as follows: -f This option is ignored by fsck_msdos, and is present only for compatibility with programs that check other file system types for consistency, such as fsck_ffs(8). -n Causes fsck_msdos to assume no as the answer to all operator questions, except ``CONTINUE?''. -p Preen the specified filesystems. -x snap-backup Use a snapshot with snap-backup as backup to check a read-write mounted filesystem. Must be used with -n. See fss(4) for more details. The point is to check an internally-consistent version of the filesystem to find out if it is damaged; on failure one should unmount the filesystem and repair it. -y Causes fsck_msdos to assume yes as the answer to all operator questions. SEE ALSO
fss(4), fsck(8), fsck_ffs(8), mount_msdos(8) BUGS
fsck_msdos is still under construction. BSD
April 11, 2010 BSD
All times are GMT -4. The time now is 02:23 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy