Along with the above it might be good to have an idea of how the hard disk is arranged. Accomplished with
. Also would help to know what accounting program or how it is set up as some go into the /usr or /usr2 areas with all the programs and data there and transferring to a new machine a matter of copying that across.
Help, if possible.
In SCO Open Server with installation of two-channel RAID controller the following happens: on the channel 0 disk array is seen by an operational system, and on the channel 1 array is not seen (simultaneously). That is the operational system can not simultaneously use more than... (1 Reply)
Hi,
I have a server that I am adding a RAID that we purchased to. The server works fine. It is running Fedora 7 and is a Dell Precision 690.
When the RAID is attached, it boots up and says the following:
Controller Bus #00, Device#1F, Function#02: 00 Ports
No device found
AHCI BIOS not... (0 Replies)
I am planning on building a fedora box with raid controller (database server).
Is anybody done that ? also what kind of software do you need to backup and recover data. (1 Reply)
I need to put together a RAID1 file server for use by Windoze systems. I've built zillions of windows systems from components. I was a HPUX SE for a long time at HP, but have been out of the game for years.
I've got an old workhorse mobo FIC PA-2013 with a 450 MHz K6 III+ I could use, but I'd... (2 Replies)
Hi All
I have a Sun T2000 server. Couple of years ago I had configured and mirrored the boot drive with an other drive using hardware RAID 1 using raidctl command.
Following is the hardware RAID output.
root@oracledatabaseserver / $ raidctl
RAID Volume RAID RAID Disk... (0 Replies)
I just built a home computer with 3TB hard drives I wanted to set up in a RAID 5 and load Ubuntu server onto it.
The first thing I did was set up the drives in a RAID 5 using just the motherboard chipset software to do it, so a 'hardware' RAID basically.
I installed Windows first to see if... (2 Replies)
First time poster and a very new Unix user, so I'll just pre-apologize for stupid questions now.
Does anybody know of a good RAID 1 hard drive backup that is Unix friendly? I want to avoid any hardcore programming. Can you recommend both NAS and non-NAS options? I need to do nightly backups... (31 Replies)
We have a 3ware RAID server at work, and as the appointed systems administrator (by virtue of being the one with the most knowledge) I've taken on the job of maintaining it. I've installed smartmontools on it to keep an eye on the drives and run scans every day, and looking at the data from the... (0 Replies)
Discussion started by: Krendoshazin
0 Replies
LEARN ABOUT DEBIAN
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)