09-30-2015
Firstly what version of Solaris is it?
In Solaris 11 all the networking configuration was changed.
8 More Discussions You Might Find Interesting
1. AIX
Hi,
We are running AIX 5.2.
Our default gateway used to be IP Address A.
Our new default gateway is IP Address B.
A netstat revealed that our default route was IP address A.
We manually added default route with IP address B and removed the default route with IP address A.
However,... (3 Replies)
Discussion started by: DenD
3 Replies
2. AIX
Hi,
After accidental default route removal serial connection doesn't work.
What should I do to connect to my machine ?
thanks
Vilius (7 Replies)
Discussion started by: vilius
7 Replies
3. Solaris
Hi,
I am new to solaris 10. What is the procedure the os takes if a default route is not configured? I am using a multihomed server with 4 interfaces. It looked strange to me this morning, because i had not defined a default route it defaulted to making one up, with the ip address of another... (9 Replies)
Discussion started by: borderblaster
9 Replies
4. AIX
Hello I have a question regarding default route on AIX servers. (I am using a p5 5.3 TL9 machine).
in my output of "lsattr -El inet0" I can see there are two routes like below.
route net,-hopcount,0,,0,x.x.207.7 Route True
route net,-hopcount,0,,0,x.x.202.129 Route True
But... (9 Replies)
Discussion started by: gsabarinath
9 Replies
5. Solaris
Hiya,
I got the default gateway set in /etc/defaultrouter file, however "netstat -nr" doesn't show anything like "default" in the routing table. As far as I know "netstat" on Solaris 10 u7 should show something like :
Routing Table: IPv4
Destination Gateway Flags Ref ... (8 Replies)
Discussion started by: TomSu
8 Replies
6. IP Networking
Greetings,
I am using debian squeeze to perform the following operation:
1. pxeboot Alix 2.c board into debian installer
When I get to the installer my laptop's dhcp server successfully provides an ip address but does not set up the default route. I am not sure how to provide this.
I... (2 Replies)
Discussion started by: mock
2 Replies
7. AIX
AIX version 5.3
when I try to add default gateway
# route add 0 192.168.100.254
Or
# route add default 192.168.100.254
I get the error
0821-275 route: socket: The file access permissions do not allow the specified action.
searching on google i came across similar... (5 Replies)
Discussion started by: filosophizer
5 Replies
8. Red Hat
Hi all,
actually i'm facing this problem,
we have 2 NICs on our VM.s with REDHAT 7.2 release,
we made the following set up as we needed to access them from both IP
ip route flush all
ip route add 10.130.11.0/24 dev eno2 tab 1
ip route add 10.130.10.0/24 dev eno1 tab 2
ip route add... (0 Replies)
Discussion started by: charli1
0 Replies
LEARN ABOUT DEBIAN
bup-margin
bup-margin(1) General Commands Manual bup-margin(1)
NAME
bup-margin - figure out your deduplication safety margin
SYNOPSIS
bup margin [options...]
DESCRIPTION
bup margin iterates through all objects in your bup repository, calculating the largest number of prefix bits shared between any two
entries. This number, n, identifies the longest subset of SHA-1 you could use and still encounter a collision between your object ids.
For example, one system that was tested had a collection of 11 million objects (70 GB), and bup margin returned 45. That means a 46-bit
hash would be sufficient to avoid all collisions among that set of objects; each object in that repository could be uniquely identified by
its first 46 bits.
The number of bits needed seems to increase by about 1 or 2 for every doubling of the number of objects. Since SHA-1 hashes have 160 bits,
that leaves 115 bits of margin. Of course, because SHA-1 hashes are essentially random, it's theoretically possible to use many more bits
with far fewer objects.
If you're paranoid about the possibility of SHA-1 collisions, you can monitor your repository by running bup margin occasionally to see if
you're getting dangerously close to 160 bits.
OPTIONS
--predict
Guess the offset into each index file where a particular object will appear, and report the maximum deviation of the correct answer
from the guess. This is potentially useful for tuning an interpolation search algorithm.
--ignore-midx
don't use .midx files, use only .idx files. This is only really useful when used with --predict.
EXAMPLE
$ bup margin
Reading indexes: 100.00% (1612581/1612581), done.
40
40 matching prefix bits
1.94 bits per doubling
120 bits (61.86 doublings) remaining
4.19338e+18 times larger is possible
Everyone on earth could have 625878182 data sets
like yours, all in one repository, and we would
expect 1 object collision.
$ bup margin --predict
PackIdxList: using 1 index.
Reading indexes: 100.00% (1612581/1612581), done.
915 of 1612581 (0.057%)
SEE ALSO
bup-midx(1), bup-save(1)
BUP
Part of the bup(1) suite.
AUTHORS
Avery Pennarun <apenwarr@gmail.com>.
Bup unknown- bup-margin(1)