Can you try booting older release of debian (i think you mentioned old ones work), just to confirm it is not the issue with kernel version or the disk itself.
If that test does not pass, check jumpers on the IDE disk, try various combinations (CS, Master, Slave).
Do you have other disks inside ?
If the test passes (old version of debian works) then post output of (during live cd or old version installed)
As root:
Code:
lshw > hw.txt
Attach the hw.txt, perhaps some bugs can be found online regarding specific hardware combinations but i cannot promise anything
I've installed rh 7.3 a fewday ago and I'm trying to boot it and I get this" Kernel panic: no init found. try passing init=options to kernel" ????? What do I do.
Thanks.
F,Ruiz. (2 Replies)
hello :-)
I have one problem with my LiLO... I installed PLD Linux on my computer but when it boots, the last thing I can see is:
request_module Root fs not mounted
VFS: Cannot open root device 03:01
Kernel panic: VFS: unable to mount root fs on 03:01
and the system stops :-(
what... (1 Reply)
I have compiled kernel version 2.6.12 in my linux box mandrake 10.1. I have followed www.digitalhermit.com/linux/Kernel-Build-HOWTO.html instructions. I have copied .config file from /usr/src/linux and lightly modified it (only the processor type) by xconfig. I have compiled the source and modules.... (3 Replies)
I am trying to Install RHEL AS 4 on x86 pc, through VNC and got the below error, Am not pretty sure as how to resolve this. Can some one guide me through the process, or what might be missing....
Have Installed RHEL, many a times but cudnt find this out...
Wud appreciate an early reply ......... (0 Replies)
ok so I just installed fedora core 6 on my dell inspiron 700m and I go to boot into linux and I get this error. Has anyone seen this before?
I also had XP Pro and Vista installed on this pc prior to putting fedora core 6 on the machine. I'm trying to setup a triple boot system.
Please Help... (2 Replies)
hello all,
please, help!
we suffered out of power today and one of our Linux boxes cannot boot properly:
..
hda set_driver_speed_status error 0X04
VFS: Unable to mount root fs on 00:00
...
the only thing that i can do - is boot in the rescue mode. i've already added noinitrd to... (2 Replies)
Hi, all:
How should I obtain the reason of kernel panic?
How should I debug the program which result in a kernel panic?
What can I get from the panic information?
li, kunlun (3 Replies)
Hi everyone,
I am trying to prevent the ehci_hcd kernel module to load at boot time.
Here's what I've tried so far:
1) Add the following line to /etc/modprobe.d/blacklist.conf (as suggested here):
2) Blacklisted the module by adding the following string to
3) Tried to blacklist the module... (0 Replies)
Hello
when i booting my SCO Server I become this Message
PLS can anyone help me?
Cheers
Christoph (1 Reply)
Discussion started by: cga
1 Replies
LEARN ABOUT HPUX
addbadsec
addbadsec(1M) System Administration Commands addbadsec(1M)NAME
addbadsec - map out defective disk blocks
SYNOPSIS
addbadsec [-p] [ -a blkno [blkno...]] [-f filename] raw_device
DESCRIPTION
addbadsec is used by the system administrator to map out bad disk blocks. Normally, these blocks are identified during surface analysis,
but occasionally the disk subsystem reports unrecoverable data errors indicating a bad block. A block number reported in this way can be
fed directly into addbadsec, and the block will be remapped. addbadsec will first attempt hardware remapping. This is supported on SCSI
drives and takes place at the disk hardware level. If the target is an IDE drive, then software remapping is used. In order for software
remapping to succeed, the partition must contain an alternate slice and there must be room in this slice to perform the mapping.
It should be understood that bad blocks lead to data loss. Remapping a defective block does not repair a damaged file. If a bad block
occurs to a disk-resident file system structure such as a superblock, the entire slice might have to be recovered from a backup.
OPTIONS
The following options are supported:
-a Adds the specified blocks to the hardware or software map. If more than one block number is specified, the entire list should be
quoted and block numbers should be separated by white space.
-f Adds the specified blocks to the hardware or software map. The bad blocks are listed, one per line, in the specified file.
-p Causes addbadsec to print the current software map. The output shows the defective block and the assigned alternate. This option
cannot be used to print the hardware map.
OPERANDS
The following operand is supported:
raw_device The address of the disk drive (see FILES).
FILES
The raw device should be /dev/rdsk/c?[t?]d?p0. See disks(1M) for an explanation of SCSI and IDE device naming conventions.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Architecture |x86 |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO disks(1M), diskscan(1M), fdisk(1M), fmthard(1M), format(1M), attributes(5)NOTES
The format(1M) utility is available to format, label, analyze, and repair SCSI disks. This utility is included with the addbadsec,
diskscan(1M), fdisk(1M), and fmthard(1M) commands available for x86. To format an IDE disk, use the DOS "format" utility; however, to
label, analyze, or repair IDE disks on x86 systems, use the Solaris format(1M) utility.
SunOS 5.10 24 Feb 1998 addbadsec(1M)
09-25-2015
