I've made an awk command that works successfully.
However I'd like to add one character to it.
For example instead of /what_i_have_now/
I'd like to change just ONE field to the opposite with an exclamation point.
Like this: ! /what_i_have_now/
My question, where am I supposed to place... (1 Reply)
I added a static route through smit using:
Communications applications and Services ==>
TCIP/IP ==>
Further Configuration ==>
Static Routes ==>
Add a Static Route ==>
Route Type of host
Filled in Destination Address, Default Gateway Address and Network Interface of en0.
This... (2 Replies)
Hello,
I'm having problems with persistent routes.
I have the route added to route-eth1.
But when I run the 'route' command to display the routes, it does not show the newly added route.
I did restart the network service. That did not help.
I also rebooted the server, but still did not... (1 Reply)
hello, i need help on setting my coyote linux, i've working on this for last 5 days, can't get it to work. I've been posting this message to coyote forum, and other linux forum, but haven't get any answer yet. Hope someone here can help me...... please see my attached picture first.
... (0 Replies)
Hi folks
Howto do quick remote health check for SAP systems on UNIX commandline? To see if a SAP system is down or in maintenace mode (no login).
I am searching something like "tnsping"/Oracle for SAP systems. (2 Replies)
I'm writing a program which uses curl to be run on Linux PCs which will be used by a number of different users. I cannot make the users all install curl on their individual machines, so I have tried to link curl in statically, rather than using libcurl.so. I downloaded the source and created a... (8 Replies)
Hi,
Just a question of thought. Why one needs to add static routes on Unix servers ? If I had ethernet card, it already has the settings for gateway for incoming and outgoing requests. We donot have to explicitly set the route it should take. Then what is the use... (3 Replies)
I have three systems A,B,C. I want to configure A in such a way that all packets from A to C goes via B.
I tried:
1. ip route add 'ip of C' via 'ip of B'
2. route add -net 'net address' netmask gw 'ip of B'
These commands work initially when I try a ping or traceroute and expire after... (2 Replies)
Hi,
I need to know what kind of firewall settings does the linux box have? Is port 25 blocked in any way?
Linux techx 3.10.0-514.10.2.el7.x86_64 #1 SMP Fri Mar 3 00:04:05 UTC 2017 x86_64 x86_64 x86_64 GNU/Linux
I'm coming from this thread. (1 Reply)
Discussion started by: mohtashims
1 Replies
LEARN ABOUT SUSE
ifsysctl
IFSYSCTL(5) Network configuration IFSYSCTL(5)NAME
ifsysctl[-<interface name>] - per network interface sysctl settings
SYNOPSIS
/etc/sysconfig/network/ifsysctl
/etc/sysconfig/network/ifsysctl-<interface name>
DESCRIPTION
These files are intended to contain sysctl settings, that should be applied when a network interface is created. This are usually interface
specific settings, like:
net.ipv6.conf.eth0.use_tempaddr = 1
or
net.ipv4.conf.eth0.rp_filter = 0
The settings are applied by the /etc/sysconfig/network/scripts/ifup-sysctl script executed via /etc/udev/rules.d/77-network.rules rule (see
udev(7)), after the creation and after the rename of the interface name to its persistent name (when applicable), but before the ifup
<interface name> -o hotplug may be executed to configure the interface.
The settings are not applied by default when the NetworkManager is active (NETWORKMANAGER=yes), except when the IFSYSCTL_NETWORKMANAGER=yes
variable is set in the /etc/sysconfig/network/config file.
Settings from the ifsysctl- file are applied every time an interface has been created.
Settings from the ifsysctl-interface name file are applied when the interface with the corresponding interface name has been created.
SYNTAX
The sysctl(8) utility is required to apply the settings. It supports two separator characters for sysctl keywords: a "." in default format
and a "/" in the alternate format. Therefore the syntax is basically same to the /etc/sysctl.conf file.
Interface names may contain a ".". In the default sysctl format using a "." as separator, that is any "." in the interface name of the key-
word, has to be replaced with a "/". In the alternate sysctl format with "/" as separator, normal interface names can be used.
Optionally, the ifsysctl files may contain also the $INTERFACE and the $SYSCTL_IF variables, that are automatically replaced with the cur-
rent interface name usable in the alternate format and with the sysctl-quoted interface name for the default format, before the settings
are passed to the sysctl utility.
Note also, that settings with variables in the ifsysctl (without the -<interface name> suffix), will be applied for every interface!
Further, files with variables are not compatible to the /etc/sysctl.conf file.
EXAMPLES
Settings for "eth0" and "eth0.1" interfaces
# using "." as separator:
net.ipv6.conf.eth0.use_tempaddr = 1
net.ipv6.conf.eth0/1.use_tempaddr = 1
# using "/" as separator:
net/ipv6/conf/eth0/use_tempaddr = 1
net/ipv6/conf/eth0.0/use_tempaddr = 1
Settings with variables:
# using "." as separator:
net.ipv6.conf.$SYSCTL_IF.use_tempaddr = 1
# using "/" as separator:
net/ipv6/conf/$INTERFACE/use_tempaddr = 1
To test your ifsysctl-eth0 or ifsysctl file, use:
/etc/sysconfig/network/scripts/ifup-sysctl eth0 -o debug
BUGS
Please report bugs at <https://bugzilla.novell.com/>
AUTHOR
Marius Tomaschewski <mt@suse.de>
SEE ALSO ifup(8)ifcfg(5)sysctl(8)sysconfig December 2009 IFSYSCTL(5)