Route get output Post: 302949865

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Route Adding

I am trying to add a route for an interface on my unix server. The interface is qfe0. How do I type out the route add command. The Normal way is route add 1.1.1.0 1.1.1.1 When I want it to bind to a certain interface how to I enter the command.

2. IP Networking

Route deleted

I am running SCOUnix OpenServer 5.0.5. For some reason a route in my routing table is being deleted and I do not know why. As far as I can see, it is nothing obvious that is deleting the route. The rest of the table is fine, only one particular entry is being delete. I run S99routes to reestablish...

3. AIX

route add

Hello , We have 3 rs/6000 server's running aix on our local network, so each time I try to ping one of these servers we get a "network is down" error , I've been instructed to use to route add command which is ... #route add server.ip router.ip after this the ping command works fine ,...

4. UNIX for Dummies Questions & Answers

no route to host

I not able to ping outside the internet. i am able to ping my 192. ip address. when i try to ping a 68. ip address i get no route to host. what should i do to correct this issue. I have sco openserver 5.05

5. IP Networking

Do I need to add a route??

I have two networks connected by cisco routers. My first subnet is 192.168.0.0 and my second is 192.168.1.0. My SCO unix machine is on the 192.168.1.0 subnet with an IP of 192.168.1.231. It can see the entire .1.0 subnet but nothing on the other network. My cicso router(gateway) to the other...

6. Solaris

SOLARIS does not route

hi, i installed solaris 9 on an SPARC server with two network interfaces. behind each interface is a small lan. i can reach every computer in every lan using one of the other interface when i am logged in the solaris. but if a computer from one lan has to connect to a computer on the other lan,...

7. UNIX for Dummies Questions & Answers

Static Route

Hi, Request you to please tell me the command or the process to add the static route in redhat linux. Thanks in Advance. Regards Arun

8. IP Networking

Route to nowhere?

Hi, HP-UX 11iV2, but it's probably universal (tcp/ip) I have a production and a test server. The test server gets the application updated nightly from the production server software. The application accesses a set of process servers on a separate subnet (192.163.22.30,31,32), but reachable...

9. Red Hat

No route to host

I get below error when using telnet and ssh ?? Why ? the ip address of linux server is 10.155.25.22 =tstgcota ?? # netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.75.0 0.0.0.0 255.255.255.0 U 0 0...

10. Shell Programming and Scripting

telnet with a certain route

OS : *NIX Shell : any I want to test telnet for a certain port on a certain machine, but via a VIP which is in front of that machine. Basically I want to follow the same route as the application does. Is there any possiblility to force telnet to follow a certain route (via the VIP I mentioned)...

LEARN ABOUT PHP

inet_type

inet_type(4)							   File Formats 						      inet_type(4)

NAME

       inet_type - default Internet protocol type

SYNOPSIS

       /etc/default/inet_type

DESCRIPTION

       The inet_type file defines the default IP protocol to use. Currently this file is only used by the ifconfig(1M) and netstat(1M) commands.

       The  inet_type  file  can  contain  a  number of <variable>=<value> lines. Currently, the only variable defined is DEFAULT_IP, which can be
       assigned a value of IP_VERSION4, IP_VERSION6, or BOTH.

       The output displayed by the ifconfig and netstat commands can be controlled by the value of DEFAULT_IP set in inet_type file.  By  default,
       both commands display the IPv4 and IPv6 information available on the system. The user can choose to suppress display of IPv6 information by
       setting the value of DEFAULT_IP.  The following shows the possible values for DEFAULT_IP and the resulting ifconfig and netstat output that
       will be displayed:

       IP_VERSION4     Displays only IPv4 related information. The output displayed is backward compatible with older versions of the ifconfig(1M)
		       and netstat(1M) commands.

       IP_VERSION6     Displays both IPv4 and IPv6 related information for ifconfig and netstat.

       BOTH	       Displays both IPv4 and IPv6 related information for ifconfig and netstat.

       The command-line options to the ifconfig and netstat commands override the effect of DEFAULT_IP as set in the inet_type file. For  example,
       even if the value of DEFAULT_IP is IP_VERSION4, the command

       example% ifconfig -a6

       will display all IPv6 interfaces.

EXAMPLES

       Example 1: Suppressing IPv6 Related Output

       This is what the inet_type file must contain if you want to suppress IPv6 related output:

       DEFAULT_IP=IP_VERSION4

SEE ALSO

       ifconfig(1M), netstat(1M)

SunOS 5.10							    16 Jun 1999 						      inet_type(4)

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Route Adding

Discussion started by: Hordak

2. IP Networking

Route deleted

Discussion started by: walkerd810

3. AIX

route add

Discussion started by: cubicle^dweller

4. UNIX for Dummies Questions & Answers

no route to host

Discussion started by: scoman2