Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: Bad magic number in disk label.
Operating Systems Solaris Bad magic number in disk label. Post 302944808 by gull04 on Friday 22nd of May 2015 06:33:38 AM
Old 05-22-2015
Hi,

Came to this a little late, is this an ultra 5 or 10.

The ultra 5 has a SCSI drive and the 10 has an IDE drive, these are quite old machines and will need some TLC.

Trditionally, the Ultra 5 had SCSI disks and the Ultra 10 had IDE.

They are both supported, to Solaris 10

Code:
43. Sun Microsystems   	Ultra 5  	Oracle Premier Support  
44. Sun Microsystems   	Ultra 10  	Oracle Premier Support

Regards

Dave
This User Gave Thanks to gull04 For This Post:
SHuKoSuGi
 

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

bad magic number

Hi, when installing a piece of third part software I get the error "Bad magic number" at one point when it tries to use libraries from the bea tuxedo server. Am I correct that this means that the software is expecting 32bit while I'm on 64bit? Is there a way around it or can it only be solved... (5 Replies)
Discussion started by: rein
5 Replies

2. Solaris

Big UH-OH "Bad magic number in disk label"

I tried rebooting my Sun server just a few minutes ago and I got the following at boot: -- Sun Fire 280R (UltraSPARC-III+) , No Keyboard Copyright 1998-2002 Sun Microsystems, Inc. All rights reserved. OpenBoot 4.5, 1024 MB memory installed, Serial #xxxxxxxxx Ethernet address... (6 Replies)
Discussion started by: deckard
6 Replies

3. Filesystems, Disks and Memory

Bad Magic Number

Dear All, i have a SCSI hard disk drive i'm installing on it solaris 5 and the workstation is sun sparc, i made an image of this H.D using Norton Ghost 6, so i took off the SCSI H.D from the sun workstation and put it on a Compaq server then i booted the server from the Norton Ghost floppy disk... (0 Replies)
Discussion started by: wesweshahaha
0 Replies

4. UNIX for Advanced & Expert Users

Bad magic number on /dev/md0

Hello All, (RHEL4) Few weeks ago I had posted a message in this forum about the problem I had when I replaced my two scsi disks and tried rebuild raid1 array. I somehow managed to up the system with working raid1 array. But the main problem persisted.. i.e when I reboot the system, mounting... (0 Replies)
Discussion started by: ravinandan
0 Replies

5. Solaris

BAD magic number in disc label...

Hello All, I m very new to this forum. i m having SUN NETRA X1 server with 40 GB HDD (Seagate) & 128 MB RAM. i m trying this server for SUN 10 Practise. As i m installing SUN 9 /10 with CD ,its giving me error after OK propmt *************************** #boot cdrom or #boot cdrom... (16 Replies)
Discussion started by: amrut_k
16 Replies

6. Solaris

Help:"Bad checksum in disk label" and "Can't open disk label package"?

Hello, I'm brand new to Sun/Solaris. I have a Sun Blade 150, with SunOS 5.8. I wanted to make a backup to prevent future data loss, so I put the disk in a normal PC with Windows XP to try to make a backup with Norton Ghost, the disk was detected, but not the file volume, so I place the disk... (6 Replies)
Discussion started by: Resadija
6 Replies

7. Solaris

Solaris 8.2 Bad magic number

I'll keep it fairly straight forward. I work with a Solaris server and magically today it decided to take a dump on me. At first it give a long list of files that couldn't be acessed before terminating the boot process and returning to the 'ok' prompt. Booting in single-user mode allowed me to run... (4 Replies)
Discussion started by: Aon
4 Replies

8. Solaris

corrupt label - wrong magic number

I have created 1 LUN. 1)LUN 00BB 200GB /dev/rdsk/c1t3d44 /dev/rdsk/c2t28d44 /dev/rdsk/c3t19d44 /dev/rdsk/c4t12d44 2) Already added the new entry into sd.conf and rebooted. 3) Already done these: powercf –q power config 4) power display dev=all I can see the new Symmetrix device.... (1 Reply)
Discussion started by: sirius20d
1 Replies

9. Solaris

Recover label, wrong magic number

Is there a way to recover label? I could install (sparc) Solaris again, but it would take a lot of time. (5 Replies)
Discussion started by: orange47
5 Replies

10. Solaris

Bad magic number error

So we have a new to us v240 server with no OS installed. It has an outdated version of OB and ALOM so before we install the OS we want to update both. We have a DVD with the latest OB patch burned on it. We do the boot cdrom command but receive the Bad Magic Number Error. Does an OS need to... (2 Replies)
Discussion started by: dunkpancakes
2 Replies

LEARN ABOUT NETBSD

trm

TRM(4)							   BSD Kernel Interfaces Manual 						    TRM(4)

NAME

     trm -- Tekram TRM-S1040 ASIC based PCI SCSI host adapter driver

SYNOPSIS

     trm* at pci? dev ? function ?
     scsibus* at trm?

DESCRIPTION

     The trm driver supports PCI SCSI host adapters based on the Tekram TRM-S1040 SCSI ASIC.

HARDWARE

     Supported SCSI controllers include:

	   Tekram DC-315 PCI Ultra SCSI adapter without flash BIOS and internal SCSI connector

	   Tekram DC-315U PCI Ultra SCSI adapter without flash BIOS

	   Tekram DC-395U PCI Ultra SCSI adapter with flash BIOS

	   Tekram DC-395UW PCI Ultra-Wide SCSI adapter with flash BIOS

	   Tekram DC-395F PCI Ultra-Wide SCSI adapter with flash BIOS and 68-pin external SCSI connector

     For Tekram DC-390 PCI SCSI host adapter, use pcscp(4) driver.

     For Tekram DC-310/U and DC-390U/UW/F PCI SCSI host adapters, use siop(4) driver.

SEE ALSO

     cd(4), ch(4), intro(4), pci(4), scsi(4), sd(4), ss(4), st(4), uk(4), scsipi(9)

     http://www.tekram.com/

AUTHORS

     The trm driver was originally written for NetBSD 1.4/i386 by Erich Chen of Tekram Technology, and Rui-Xiang Guo rewrote the driver to use
     bus_space(9) and bus_dma(9) for NetBSD 1.6.

BSD
								 November 6, 2001							       BSD
All times are GMT -4. The time now is 03:40 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy