Not much of ipv6 experience i have, but here are some thoughts:
You are setting an IP manualy, have you disabled dhcp?
You are setting a 2nd ipv6 adress to your device.
To my eyes, the ipv6 you are setting, seems invalid (quite too short).
Hi gurus,
In a few month, we must enable IPv6 on our Linux Server!
Should we reinstall the Linux machine to enable IPv6 or could we just make some change in configuration's files?
Could Linux run simultaneous IPv4 and IPv6?
Thanks in advance for our help our ideas?
Best regards,
nm (3 Replies)
I have perl script that I use to check and ping a list of ip,
The problem is, I didnt understand how to ping ipv6 on perl,
Could I use Ping::External??And how could I get the ping result (reply or not)?
This is my code
#!/usr/bin/perl --
use Net::Ping;
use Data::Validate::IP;
use... (3 Replies)
Hi,
I develop simple animation ping script on Solaris Platform. It is like Cisco ping.
Examples and source code are below.
bash-3.00$ gokcell 152.155.180.8 30
Sending 30 Ping Packets to 152.155.180.8
!!!!!!!!!!!!!.!!!!!!!!!!!!!!!.
% 93.33 success... % 6.66 packet loss...... (1 Reply)
Hi
I am using perl to ping a list of nodes - with script below :
$p = Net::Ping->new("icmp");
if ($p->ping($host,1)){
print "$host is alive.\n";
}
else {
print "$host is unreacheable.\n";
}
$p->close();... (4 Replies)
I am currently trying to setup static ipv6 address with a persistent default gateway. This is on a Solaris 10 non global zone running inside a Solaris 10 global zone. My production server I am comparing against is a Solaris 10 xen instance running on a Oracle Solaris xen instance.
I have got... (12 Replies)
Hi,
I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output. Below are few files and command output for your... (1 Reply)
help with bash script!
im am working on this script to make sure my server will stay online, so i made this script..
HOSTS="192.168.138.155"
COUNT=4
pingtest(){
for myhost in "$@"
do
ping -c "$COUNT" "$myhost" &&return 1
done
return 0
}
if pingtest $HOSTS
#100% failed... (4 Replies)
I'm running a Linux OS that uses Debian as it's base. A commercial vpn is installed that uses OpenVPN. For some reason, I can't get ipv6 to tunnel properly .... and Ipleak.net shows that my location is being unmasked by ipv6.
I've tried kernel commands at boot, I've tried sysctl.conf commands.... (2 Replies)
Discussion started by: benc
2 Replies
LEARN ABOUT DEBIAN
mrtg-ping-probe
MRTG-PING-PROBE(1) General Commands Manual MRTG-PING-PROBE(1)NAME
mrtg-ping-probe - ping probe module for Multi Router Traffic Grapher
DESCRIPTION
mrtg-ping-probe is a ping probe module for MRTG 2.x. It is used to monitor the round trip time and packet loss to networked devices. MRTG
uses the output of mrtg-ping-probe to generate graphs visualizing minimum and maximum round trip times or packet loss.
mrtg-ping-probe is not run directly, but is called by MRTG as a helper when it needs to determine ping time to a host.
Act responsibly: do not use mrtg-ping-probe to ping devices without the owner's permission. Just imagine if 10,000 people decided to ping
your hosts! mrtg-ping-probe is meant to be used within your network to get round trip time performance figures for your network.
OPTIONS
To use mrtg-ping-probe you need to configure MRTG to call it from within the definition of a target host. This is done in the MRTG config
file, which is usually /etc/mrtg.conf.
Here's an example snippet: change the target name and IP address to suit your needs.
Target[your.target.ping]: `/usr/bin/mrtg-ping-probe 123.456.789.123`
SetEnv[your.target.ping]: MRTG_INT_IP="123.456.789.123" MRTG_INT_DESCR="ping"
MaxBytes[your.target.ping]: 100
AbsMax[your.target.ping]: 200
Options[your.target.ping]: gauge, growright
YLegend[your.target.ping]: ping time (ms)
ShortLegend[your.target.ping]: ms
Legend1[your.target.ping]: Maximum Round Trip Time in ms
Legend2[your.target.ping]: Minimum Round Trip Time in ms
Legend3[your.target.ping]: Maximal 5 Minute Maximum Round Trip Time in ms
Legend4[your.target.ping]: Maximal 5 Minute Minimum Round Trip Time in ms
LegendI[your.target.ping]: Max:
LegendO[your.target.ping]: Min:
Pay close attention to the backticks in the first line which tell MRTG to execute the nominated external program. Note also that you need
to use the "gauge" option, since the results of subsequent ping probes are independant values and not an incrementing counter.
SEE ALSO mrtg(1).
The latest release of mrtg-ping-probe can be found on the web at http://pwo.de/projects/mrtg/
AUTHOR
This manual page was written by Jonathan Oxer <jon@debian.org>, for the Debian project (but may be used by others).
April 14, 2003 MRTG-PING-PROBE(1)