to
Note that I swapped the order of the fields in the structure.
By defining the structure with the smaller elements first, if the structure is packed tightly, as it likely is under optimization, you're likely violating an address restriction on the value when you pass it like that.
This may belong in the C Programming forum, but here goes anyway...
What would cause a bus error? I searched google for a cause, but came up with some conflicting reports...
Could it be caused by disk space?
A lot of the pages I found mentioned linking with the incorrect versions of the... (4 Replies)
Hi there
I am running soalris 9 on a sun fire 480r and all of a sudden (today) whenever the users run the command `top` we get the following message `bus error`
does anybody have any information on what this is all about and whether there is a routine i can perform to gather more... (3 Replies)
Hi!
I've got a program which runs fine under Linux, but I have compiled it to run under SunOS 5.8 in a Sparc computer, and now it sometimes fails with "bus error".
Ussing gdb I surfed to the error line, which is
*pointer = some_vector;
where some_vector is a 16 byte struct (4 integers)... (1 Reply)
Hi there,
I have two SunBlade 2000s that I want to connect to a single D1000. I am told that I need to do a split bus mode. I don't really understand what that means. Does that mean that half of the storage disks will be assigned to one host and the others to the other host? How do I get... (18 Replies)
Hi all,
I am getting bus error problem in SunOS. Can you please help me out in this regard.
Actually, my entire code till the last line has been executed. But after tht i am getting a bus error. Please help me.
Thanks in advance.
Charu. (4 Replies)
I am getting bus error when i include "#!/bin/ksh". If i remove interpreter then script is working. Can anyone explain this and how can i avoid this error?
Operating System is HP-UX B.11.23 U 9000/800 1091834454 (2 Replies)
Hi everyone,
I have a GUI project and when I run it and left in idle state for a long time(there is nothing done, just opened GUI, no more actions),I get bus error after trying to do anything with it.
I've tried to build it in debug mode and use gdb, but I don't get any error in debug mode.It... (3 Replies)
Hi all,
I am writing a phonebook program to store names and number using a list. Here is the code for the function which allows the user to enter the name and number (where the error occurs).
//THIS FUNCTION ADDS A NEW ENTRY TO THE phonebook_list
void insert(void){
//variables
int... (5 Replies)
Hi all,
OS is Solaros 10 Sparc
While doing Netbackup upgradation to 7.5 , the server was asked to reboot.
But then it came up in single user mode,
and after I typed format command it showed some disk error.
bash-3.00# format
Searching for disks...WARNING:... (2 Replies)
Discussion started by: manalisharmabe
2 Replies
LEARN ABOUT LINUX
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)