hi,
i downloaded wget-1.9.1-sol9-sparc-local.gz for solaris sparc 9. but do not know how to install it.
anybody help me.
many thanks
tinhlx (3 Replies)
I'm trying to do an upgrade/install from Solaris 8 to Solaris 10 on a SUN Sparc system.
I halt the system, as documented, but when I attempt to boot off the distribution DVD; i.e.
halt
:
:
OK> boot cdrom
The system indicates that the device is 'unrecognizable'
These are SUN... (5 Replies)
I downloaded the iso image from here and burnt it on DVD.
But when I tried installing it..it said boot device not availiable. Do I have to make it bootable?
Is there any other component that I need to write on DVD other than the image?
Moreover the DVD which I received from my admin for... (5 Replies)
I recently got a Sun Sparc 10 Ultra with Solaris 10 installed on it. Now I'm trying to connect my SCSI Jaz drive to it. I moved my Adaptec AHA-2940U PCI SCSI card from my XP PC (where it was working OK) to the Sun and that's about as far as I got.
I did a probe-scsi-all and got nothing back,... (0 Replies)
Certainly these servers have quite a few differences, not the least of which include CPU architecture and OEM. But, I'm wondering which would offer the greater reliability and availability. Thoughts? (3 Replies)
hi everyone,
good day to all.
I need help to fix an issue which we encounter while installing the Alcatel -lucent 5620 NM on a solaris 10 OS.
The Alcatel lucent 5620 NM release 9 software is only recommended OS to work with Solaris 10 release 5/09 but when we try to install the same... (9 Replies)
Hi
The following is the output of "df -h" and "zfs list" right after fresh installation of Solaris 11.3 on Sparc T5-2 with 256GB memory. Because the server has 256GB of memory, I think Solaris created swap file system mounted on /system/volatile and /tmp, but my question is, zfs also has... (5 Replies)
Discussion started by: jasonu
5 Replies
LEARN ABOUT DEBIAN
hd
HD(4) Linux Programmer's Manual HD(4)NAME
hd - MFM/IDE hard disk devices
DESCRIPTION
The hd* devices are block devices to access MFM/IDE hard disk drives in raw mode. The master drive on the primary IDE controller (major
device number 3) is hda; the slave drive is hdb. The master drive of the second controller (major device number 22) is hdc and the slave
hdd.
General IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the
partition on that physical drive. The first form, hdX, is used to address the whole drive. Partition numbers are assigned in the order
the partitions are discovered, and only nonempty, nonextended partitions get a number. However, partition numbers 1-4 are given to the
four partitions described in the MBR (the "primary" partitions), regardless of whether they are unused or extended. Thus, the first logi-
cal partition will be hdX5. Both DOS-type partitioning and BSD-disklabel partitioning are supported. You can have at most 63 partitions
on an IDE disk.
For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS "primary" partition on the
second one.
They are typically created by:
mknod -m 660 /dev/hda b 3 0
mknod -m 660 /dev/hda1 b 3 1
mknod -m 660 /dev/hda2 b 3 2
...
mknod -m 660 /dev/hda8 b 3 8
mknod -m 660 /dev/hdb b 3 64
mknod -m 660 /dev/hdb1 b 3 65
mknod -m 660 /dev/hdb2 b 3 66
...
mknod -m 660 /dev/hdb8 b 3 72
chown root:disk /dev/hd*
FILES
/dev/hd*
SEE ALSO chown(1), mknod(1), sd(4), mount(8)COLOPHON
This page is part of release 3.44 of the Linux man-pages project. A description of the project, and information about reporting bugs, can
be found at http://www.kernel.org/doc/man-pages/.
Linux 1992-12-17 HD(4)