Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (2 Replies)
Hi,
I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch... (4 Replies)
Me again :)
I'm trying to find a page describing the L2, L3 und L4 modes of dladm.
It's nice to read "hashed by ip header", but how should I use that?
On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Hi All, I am trying to aggregate the NIC's,(igb2 and igb3) (igb0 is used by the physical system and igb1 is used by primary-vsw0) to create the domains on that for faster data transfer, I followed the process for creating the aggregation, dladm create-aggr -d igb2 -d igb3 1
after creating the... (2 Replies)
Hi,
I want to Break the Link Aggregation. My aggregation are lan0+lan1 = lan900.
Now I want to break this and put the IP in lan0. But i have cluster environment and this is the main database server.
So It need to change in cluster script.
But I dont know where I have to change it.
Please... (1 Reply)
Hi,
I'm not from the Solaris world and some of these things are new to me. Can someone tell me if it is possible to configure link aggregation without using LACP?
I am told etherchannel was setup without LACP. (3 Replies)
Hi
ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ?
are there any script and services do that... (0 Replies)
Hi,
This is Solaris-10 x86 platform.
I am not able to ping gateway associated with aggr50001. I am not getting idea, where could be issue. Please advise.
# netstat -nr
Routing Table: IPv4
Destination Gateway Flags Ref Use Interface
--------------------... (10 Replies)
Hi,
I have Solaris-10 server and link aggregation is configured on this in below way
# dladm show-aggr
key: 1 (0x0001) policy: L4 address: 3c:d9:2b:ee:a8:a (auto)
device address speed duplex link state
bnx1 3c:d9:2b:ee:a8:a... (8 Replies)
Discussion started by: solaris_1977
8 Replies
LEARN ABOUT OPENSOLARIS
wpad
wpad(1M) System Administration Commands wpad(1M)NAME
wpad - WPA and WPA2 protocol daemon
SYNOPSIS
/usr/lib/inet/wpad [-i interface] [-k pre_shared_key_name]
DESCRIPTION
The wpad daemon provides common client functionality for the WiFi Protected Access (WPA) versions 1 and 2, as defined by IEEE802.11i stan-
dard. WPA was created by the WiFi Alliance, an industry trade group. WPA implements the majority of the IEEE 802.11i standard, and was
intended as an intermediate measure to take the place of Wired Equivalent Privacy (WEP) while 802.11i was prepared. WPA2 implements the
full standard.
wpad provides the following WPA/IEEE 802.11i features:
o WPA-PSK ("WPA-Personal")
o Key management for CCMP, TKIP, WEP104, WEP40
Stop and start the wpad daemon using dladm(1M). Use:
# dladm connect-wifi
...to start the wpad daemon. Use:
# dladm disconnect-wifi
...to stop the daemon.
OPTIONS
The following options are supported:
-i interface
Specify a WiFi Link interface to start the wpad daemon.
-k pre_shared_key_name
Specify the pre-shared key used for the WiFi Link.
EXAMPLES
Example 1 Starting the wpad Daemon on Specific WiFi Link
To create the WPA key psk, enter the following command:
# dladm create-secobj -c wpa psk
To use key psk to connect to ESSID wlan on link ath0, enter the following command:
# dladm connect-wifi -k psk -e wlan ath0
Example 2 Stopping the wpad Daemon on Specific WiFi Link
To stop the daemon on the link ath0, enter:
# dladm disconnect-wifi ath0
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWwpau, SUNWwpar |
+-----------------------------+-----------------------------+
|Interface Stability |Uncommitted |
+-----------------------------+-----------------------------+
SEE ALSO svcs(1), dladm(1M), svcadm(1M), attributes(5), smf(5)NOTES
The wpad service is managed by the service management facility, smf(5), under the service identifier:
svc:/network/wpa:<link>
Administrative actions on this service, such as enabling, disabling, or requesting restart, can be performed using svcadm(1M). The ser-
vice's status can be queried using the svcs(1) command.
SunOS 5.11 11 Mar 2008 wpad(1M)