I've copied over the sol-11_2-text-sparc.usb file to a USB thumb drive, plugged into a USB port on the front of the server, and then attempted to find the drive with
to no avail.
Is there a different way to copy the image over to the drive using a Windows workstation? Is there anything else I should be doing in order to make sure that the server recognizes the USB thumb drive?
Hi all,
I've managed to get Mandrake 9 installed by disconnecting my 2 windows' drives. When I reconnect them Mandrake wants to take over. I figure it's time for the BootManager, or should I use a Linux specific one like Lilo? Or have I already stuffed up by not running Lilo at time of... (2 Replies)
I got Puppy linux and installed it on a usb stick.
In the BIOS i selected to boot from USB-FDD but it goes to my HD and ignores the USB stick,
What going on ?? (2 Replies)
ok so i have recently aquired an old Apple network server 700, its running AIX 4.1.4, i have virtually no experience in unix, it come up with
"Can't open disk lebel package can't OPEN: /bandit/53c825@2,0:aix"
i tried the maintinance mode with the AIX CD and i guess reinstalled, at least it... (1 Reply)
I have downloaded KNOPIIX and burned it on a CD, it niether boots from CD nor could I open the file, it seems the extension is .iso, would you mind sending me your comment,please.
Thank you very much (2 Replies)
I installed RH8 on Thinkpad R51. The install went smooth, but when I tried to boot, it hanged at:
PCI_IDE: unknown IDE controller on Pci bus 00 device f9, VID=8086, ID=24ca
PCI: Device 00:1f.1 not available because of resource collisions.
PCI_IDE: (ide_setup_pci_device:) could not enable... (0 Replies)
Hello..
I am Still Learing Solaris ..
when i try to Install Solaris 8 from its CD...i pressed STOP + A and i get a OK prompt screen.
I then typed, "boot cdrom" and i am getting this error message.
" FATAL: system is not bootable, boot command is disabled."
How do we enable the boot... (5 Replies)
I first had windows xp 64-bit installed on my system, and then installed fedora 10 on a partition (partition was created while installing fedora).
When installation was completed, I could not boot on Windows or Fedora, I keep on getting this disc error and system asking to press ctrl+alt+del to... (0 Replies)
Hello,
I have an 8gb usb flash drive that I had high aspirations of using for a recovery/install/messing around multipurpose drive.
fdisk shows:
$ sudo fdisk -l /dev/sdb
password for woodnt:
Disk /dev/sdb: 8036 MB, 8036285952 bytes
255 heads, 63 sectors/track, 977 cylinders
Units =... (0 Replies)
Is there an easy way to setup a cross-over cable (USB-USB) between a linux box and a windows PC? My 2 machines are next to each other but I really do not want to keep transfering my files using my USB drive.
Thanks! (4 Replies)
Discussion started by: Xterra
4 Replies
LEARN ABOUT FREEBSD
usb_template
USB_TEMPLATE(4) BSD Kernel Interfaces Manual USB_TEMPLATE(4)NAME
usb_template -- USB templates
SYNOPSIS
To compile this module into the kernel, place the following line in your kernel configuration file:
device usb_template
To load the module at boot time, place the following line in loader.conf(5):
usb_template_load="YES"
DESCRIPTION
The usb_template module implements various USB templates that are needed when programming an USB device side driver. A USB template consists
of an USB device descriptor, one or more USB configuration descriptors, one or more USB interface descriptors, one or more USB endpoint
descriptors, USB strings and additional USB descriptors. The USB template module currently has templates for USB Mass Storage, USB CDC Eth-
ernet and Message Transfer Protocol. USB templates are currently selected using the "hw.usb.template" sysctl. The "hw.usb.template" value
can be changed at any time, but will not have any effect until the USB device has been re-enumerated.
SEE ALSO usb(4)STANDARDS
The usb_template module complies to the USB 1.0, 2.0 and 3.0 standard.
HISTORY
The usb_template module was written by Hans Petter Selasky <hselasky@FreeBSD.org>.
BSD March 18, 2014 BSD