01-26-2015
There is no eth0 on a T2000 running Solaris, this is a Linux terminology. The standard network interfaces are NETMGT and NET0 to NET4. Which one are you talking about?
In any case, your OS is either suspended or not booted according to your last reply so there is no way to access it (yet).
Run "go" or "boot" from the "ok" prompt to either resume or boot the OS.
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
No, its not a movie, its a command to get you from the sc> ALOM prompt back to the console or ok prompt.
You must log into the ALOM, then to jump back to the console enter "console -f".
Problem is that this leaves you logged in on the ALOM.
Question: is there an escape key sequence to get... (1 Reply)
Discussion started by: jsy
1 Replies
2. Solaris
Hello Guys,
I am working with sunfire V480 and wants to know how to connect to alom. Can you please guide? (7 Replies)
Discussion started by: mokkan
7 Replies
3. Solaris
hello guys.... I'm newbie in solaris server / os, anybody know how disable alom server v240.
thank u (9 Replies)
Discussion started by: yanto85
9 Replies
4. Solaris
Hi guys,
I'm in trouble with a Sunfire T2000.
The OS (Solaris10) is up and running, but I can't log in the sc>I think the terminal server is crashed!
Does anyone know if I can reset the sc> from the OS?
How can I do that?
Thx (6 Replies)
Discussion started by: cecco16
6 Replies
5. Solaris
Hi Everyone.
What is the differece b/n ALOM and ALOM CMT Service processor.
I am trying reset ALOM login/passwd using scadm utility on T2000, while I am googling I came cross ALOM CMT doesnt support scadm utility, but ALOM supports.
Not sure how different are these.
Thanks, (0 Replies)
Discussion started by: bobby320
0 Replies
6. Solaris
I have a few servers that are all having the same problem when trying to login to their ALOMs. The are T2000's. When I go to login I get the login prompt, but some machines ALOMs aren't responding to the initial login:
# ssh xx.xx.xx.xx
Copyright 2008 Sun Microsystems, Inc. All rights... (9 Replies)
Discussion started by: christr
9 Replies
7. Solaris
Hi gurus,
I have a sun netra 240 server. I want to get to the ALOM but it always ask for login and password. Can anyone tell me how I can reset the ALOM it to default so I can be able to configure it?
Thanks lots. (2 Replies)
Discussion started by: cjashu
2 Replies
8. Solaris
Hello forum,
I have a SUN v250 at home that I have to practice Solaris. I currently have Solaris 9 installed and the ALOM Sun(tm) Advanced Lights Out Manager 1.5.2.
From the ALOM I want to access the console.
sc> console -f
Enter #. to return to ALOM.
after that there is no response.... (19 Replies)
Discussion started by: br1an
19 Replies
9. Solaris
Hi guys,
I'm new with solaris.
I just received sunfire T2000 server.
Problem:
ALOM keep hang/stuck/jammed.
Steps do before it hang :
1. Connect to T2000 (using RJ45 - DB9 cable)
2. Open putty, connect via serial.
3. Power on the server.
4. Its loading.
5. then, hang.
... (1 Reply)
Discussion started by: rajasraf
1 Replies
10. Hardware
Hi all,
I have some problems with the fan FT0.F0, which looks like has a problem with the PROM/ALOM ( I am nor sure who).....but, in fact, the fan is working properly even in other V440 Sparc Server.
We checked HW comunication between Fan and the MotherBoard, and we think is a problem of... (8 Replies)
Discussion started by: proof_enrique
8 Replies
BOOTP(8) System Manager's Manual BOOTP(8)
NAME
bootp, rarpd, tftpd - Internet booting
SYNOPSIS
ip/bootp [-d]
ip/rarpd [-d] [-e etherdev]
ip/tftpd [-dr] [-h homedir]
DESCRIPTION
These programs support booting over the Internet. They should all be run on the same server to allow other systems to be booted. Bootp
and tftpd are used to boot everything; rarpd is an extra piece just for Suns.
Bootp passes to Plan 9 systems their IP address, IP mask, default boot file, default file server, default authentication server, and
default gateway. These come from the network database file attributes ip, ipmask, bootf, fs, auth, and ipgw attributes respectively (see
ndb(6) and ndb(8)). The attributes come from the entry for the system, its subnet, and its network with the system entry having prece-
dence, subnet next, and network last. Bootp will answer requests only if it has been specifically targeted or if it has read access to the
boot file for the requester. The -d option causes debugging to be printed to standard output.
Rarpd performs the Reverse Address Resolution Protocol, translating Ethernet addresses into IP addresses. The options are:
d print debugging to standard output
e use the Ethernet mounted at /net/etherdev
Tftpd transfers files to systems that are booting. It runs as user none and can only access files with global read permission. The
options are:
d print debugging to standard output
h change directory to homedir. The default is /lib/tftpd. All requests for files with non-rooted file names are served starting at
this directory with the exception of files of the form xxxxxxxx.SUNyy. These are Sparc kernel boot files where xxxxxxxx is the hex
IP address of the machine requesting the kernel and yy is an architecture identifier. Tftpd looks up the file in the network data-
base using ipinfo (see ndb(2)) and responds with the boot file specified for that particular machine. If no boot file is specified,
the transfer fails. Tftpd supports only octet mode.
r restricts access to only files rooted in the homedir.
SOURCE
/sys/src/cmd/ip
SEE ALSO
ndb(6)
BOOTP(8)