Thanks for the reply. Pl find the below outputs of the Server implemented Hardware raid. Kindly guide me , I have not done patching in these Hardware raid implemented Servers.
1. Uname -a :
2.
3. df -h
Thanks and regards ,
Rj
Last edited by DukeNuke2; 01-11-2015 at 02:25 PM..
I don't understood why on SPARC-Platforms have not present RAID-Controller ? Sorry for my bad english, but it's crazy always setup software RAID !!! I whanna Hardware RAID and when i can find solution ? (7 Replies)
Hi,
I have t5120 sparc and I have 2 146 G drives in the system. I will be installing solaris 10 and also want the system mirrored using Hardware RAID "1"
The System did come preinstalled as it comes from sun. I did not do much on it.
I booted system using boot cdrom -s
gave format... (6 Replies)
Hi,
I have a root with hardware RAID on c0t0d0 and c0t2d0. I would like to set the boot device sequence in OBP for both hdds.
I have checked in ls -l /dev/rdsk/ for the path of c0t2d0 but it does not exist. Can anyone shed some lights on this?
AVAILABLE DISK SELECTIONS:
0.... (12 Replies)
Hi,
I have a question. Do LiveUpgrade supports hardware raid?
How to choose the configuration of the system disk for Solaris 10 SPARC?
1st Hardware RAID-1 and UFS
2nd Hardware RAID-1 and ZFS
3rd SVM - UFS and RAID1
4th Software RAID-1 and ZFS
I care about this in the future to take... (1 Reply)
Hi all
I've just received my T3-1. It has 8 disks and I would like to configure RAID1 on the disks. The Sun documentation states that you can either use the OpenBoot PROMP utility called Fcode or you can use software via the Solaris OS.
The documentation doesn't make it clear if:
1. The... (6 Replies)
Server Model: T5120 with 146G x4 disks.
OS: Solaris 10 - installed on c1t0d0.
Plan to use software raid (veritas volume mgr) on c1t2d0 disk.
After format and label the disk, still not able to detect using vxdiskadm.
Question:
Should I remove the hardware raid on c1t2d0 first?
My... (4 Replies)
Dear All ,
We need to do patching on one Solaris Server , where we have raid 0 configured.
What is the process to patch a Server if RAID 0 (Concat/Stripe) is there.
Below is the sample output.
# metadb
flags first blk block count
a m pc luo 16 ... (1 Reply)
Dear All ,
Pl find the below command ,
# raidctl -l
Controller: 1
Volume:c1t0d0
Disk: 0.0.0
Disk: 0.1.0
Disk: 0.3.0
#
raidctl -l c1t0d0
Volume Size Stripe Status Cache RAID
Sub Size ... (10 Replies)
Discussion started by: jegaraman
10 Replies
LEARN ABOUT OPENSOLARIS
oplhpd
oplhpd(1M) System Administration Commands oplhpd(1M)NAME
oplhpd - Hot plug daemon for SPARC Enterprise Server line
SYNOPSIS
/usr/platform/SUNW,SPARC-Enterprise/lib/sparcv9/lib/oplhpd
DESCRIPTION
The hot plug daemon for SPARC Enterprise Servers is a daemon process that runs on the SUNW,SPARC-Enterprise family of servers. The daemon
is started by the service management facility (see smf(5)) and communicates with the service processor when hot plug PCI cassettes change
their dynamic reconfiguration state.
The service FMRI for oplhpd is:
svc:/platform/sun4u/oplhpd:default
A domain supports only one running oplhpd process at a time.
ERRORS
OPLHPD uses syslog(3C) to report status and error messages. All of the messages are logged with the LOG_DAEMON facility.
Error messages are logged with the LOG_ERR and LOG_NOTICE priorities, and informational messages are logged with the LOG_DEBUG priority.
The default entries in the /etc/syslog.conf file log all of the OPLHPD error messages to the /var/adm/messages log.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWdcsu, SUNWdcsr |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
SEE ALSO svcs(1), inetadm(1M), svcadm(1M), syslog(3C), syslog.conf(4), attributes(5), smf(5)SunOS 5.11 23 May 2006 oplhpd(1M)