12-23-2014
The disks have actually the same size, reported as exactly 300000000000 bytes. The s2 partition (or slice) is not really the whole disk but the accessible part of it.
The difference is due to the way the disks firmware defines their geometry.
Two cylinders are reserved by Solaris on each disk and the fact the cylinder size differs make the available space slighty smaller on one of the disks.
If you are adventurous, you might try twiddling with the format command to try setting the disk type of the new disk to the same one as the older one.
When was created the pool ?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Please help me!!!. I am new to Unix and I have to replace the tape backup drive. Originally the system had an IBM tape drive (Rhomat) that is damged. I changed it and installed a dat drive HP 5000+. The hardware recognize the drive, the diagnostics if OK. But when I try to install the operating... (3 Replies)
Discussion started by: allaite2
3 Replies
2. Shell Programming and Scripting
Hi folks,
I have the following configuration file:
tofu:/tmp # cat bitbandConfig.properties
maestroIp=10.10.10.10
maestroPort=2020
adminPlayPath=<Streaming Agent IP>:2021/streamingGateway/GetPlayList
###This part should not be changed###
adminPlayVODProtocol=http
username=iptv... (7 Replies)
Discussion started by: nir_s
7 Replies
3. AIX
My root disk is failed and how to replace the root disk in AIX.
Can u give a detailed explanation in step wise.
Pls give the answer taking different scenarios.
Regards
Praveen (1 Reply)
Discussion started by: chinnu_mulakala
1 Replies
4. UNIX for Dummies Questions & Answers
Any help appreciated
Sco Unix Ver 5.0+
Have 2 90 gig mirrored drives
Can these be replaced with any similar drive?
Can one just be replaced and will the mirror rebuild on it and then allow reboot on it ---then replace 2nd drive?
Thanks
pb (3 Replies)
Discussion started by: paul1730
3 Replies
5. OS X (Apple)
I am trying to recover data off a drive that failed in my iMac. Apple returned the drive to me and I purchased a hard drive enclosure. I have been doing research on prices for data recovery services, way too expensive. I seen some links using Unix DD commands in the terminal none of which worked.... (6 Replies)
Discussion started by: KJ1906
6 Replies
6. Infrastructure Monitoring
Here are the details.
cnjr-opennms>root$ zfs list
NAME USED AVAIL REFER MOUNTPOINT
openpool 20.6G 46.3G 35.5K /openpool
openpool/ROOT 15.4G 46.3G 18K legacy
openpool/ROOT/rds 15.4G 46.3G 15.3G /
openpool/ROOT/rds/var 102M ... (3 Replies)
Discussion started by: pupp
3 Replies
7. Solaris
Dear all
Please can any one explain me how to replace failed disk in Solaris 10.
Please tell me the step by step procedure. (9 Replies)
Discussion started by: suneelieg
9 Replies
8. Solaris
-bash-3.00# zpool detach zonepool c1t1d0
cannot detach c1t1d0: only applicable to mirror and replacing vdevs
-bash-3.00# zpool remove zonepool c1t1d0
cannot remove c1t1d0: only inactive hot spares, cache, top-level, or log devices can be removed
-bash-3.00# zpool offline zonepool c1t1d0... (3 Replies)
Discussion started by: LittleLebowski
3 Replies
9. AIX
I am new to the AIX operating system and am seeking out some advice. We recently have had a drive go bad on our AIX server that is in a RAID 10 array. We have a replacement on the way. I was wondering what the correct steps are to swap out this drive. Does the server need to be powered off? Or can... (5 Replies)
Discussion started by: mpeter05
5 Replies
10. AIX
I have a AIX 7.1 system that has 3 failed disks, 1 in rootvg and 2 in vg_usr1.
Here is the output of lspv.
# lspv
hdisk0 00044d4dfbb11575 vg_usr1 active
hdisk1 0000150179158027 vg_usr1 active
hdisk2 ... (11 Replies)
Discussion started by: c3rb3rus
11 Replies
LEARN ABOUT ULTRIX
disktab
disktab(5) File Formats Manual disktab(5)
Name
disktab - disk description file
Syntax
#include <disktab.h>
Description
The file is a simple data base that describes disk geometries and disk partition characteristics. The format is patterned after the termi-
nal data base. Entries in consist of a number of fields separated by colons (:). The first entry for each disk gives the names that are
known for the disk, separated by vertical bars (|). The last name given should be a long name fully identifying the disk.
The following list indicates the normal values stored for each disk entry:
Name Type Description
ns num Number of sectors per track
nt num Number of tracks per cylinder
nc num Total number of cylinders on the disk
ba num Block size for partition `a' (bytes)
bd num Block size for partition `d' (bytes)
be num Block size for partition `e' (bytes)
bf num Block size for partition `f' (bytes)
bg num Block size for partition `g' (bytes)
bh num Block size for partition `h' (bytes)
fa num Fragment size for partition `a' (bytes)
fd num Fragment size for partition `d' (bytes)
fe num Fragment size for partition `e' (bytes)
ff num Fragment size for partition `f' (bytes)
fg num Fragment size for partition `g' (bytes)
fh num Fragment size for partition `h' (bytes)
pa num Size of partition `a' in sectors
pb num Size of partition `b' in sectors
pc num Size of partition `c' in sectors
pd num Size of partition `d' in sectors
pe num Size of partition `e' in sectors
pf num Size of partition `f' in sectors
pg num Size of partition `g' in sectors
ph num Size of partition `h' in sectors
se num Sector size in bytes
ty str Type of disk (e.g. removable, winchester)
The entries can be automatically generated with the program.
Files
See Also
chpt(8), newfs(8)
disktab(5)