Sponsored Content
Full Discussion: Error on network card
Operating Systems Linux Ubuntu Error on network card Post 302929616 by rbatte1 on Tuesday 23rd of December 2014 11:35:39 AM
Old 12-23-2014
I know that these may be a daft questions, but:-
  • What are you expecting?
  • Do you have cables in all the cards, connected to switches etc.?
  • Are your definition files set up (presuming it's /etc/sysconfig/network-scripts/ifcfg-eth3 in this case)
  • Should it/they be DHCP or STATIC addresses?
  • If DHCP, is there a server that can service the DHCP request?
I'm just trying to get a better picture of your needs to make sure we get you the best answers.


Thanks, in advance,
Robin

Last edited by rbatte1; 12-23-2014 at 12:36 PM.. Reason: Added another question
 

10 More Discussions You Might Find Interesting

1. IP Networking

network card

I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies

2. Cybersecurity

network card physical reset error

Hi all I am facing some problem with network card i am using solaris8 and on sunultra10 .As it is my firewal machine i have got on backup harddisk for any emergency. In one hardidsk while installation only hme0 interface was configured and in the backup hard disk qfe0/hme0 both are... (0 Replies)
Discussion started by: Prafulla
0 Replies

3. UNIX for Dummies Questions & Answers

Installing network card

1) i am trying to install realtek network card in caldrea linux, but i am not able to find the interface, 2)i download drivers for network card and i am not able to read the floopy in linux, pls help me out. (1 Reply)
Discussion started by: gops
1 Replies

4. IP Networking

Network Card with SGI

The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out > link ok < when i connected > But... (0 Replies)
Discussion started by: DPAI
0 Replies

5. UNIX for Advanced & Expert Users

Network Card Help

I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies

6. UNIX for Advanced & Expert Users

network card problem

hi, everyone: alpha 600 au true64 Unix 4.0f my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages. "tu0 :transmit FIFO underflow:threshold raised to :256 byteŁ¬link up... (1 Reply)
Discussion started by: q30
1 Replies

7. Solaris

[need help] error after configure network card at v890 sparc

hi experts, i have some problem with my server v890, i had config the network with ce0,ce1 and eri0 but after reboot the server have this error messages display : WARNING: ce0: fault detected external to device; service degraded WARNING: ce0: xcvr addr:0x01 - link down configuring IPv4... (2 Replies)
Discussion started by: bucci
2 Replies

8. UNIX for Dummies Questions & Answers

How can I tell which network card is which?

I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink? Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies

9. Solaris

How to identifying the network card ?

Hi Experts, Can we use some command from unix to find the available network interface? I did tried Its listing following, however how can I decide the which vender card is attached e.g. if its hme , bge or some thing else Thanks (7 Replies)
Discussion started by: kumarmani
7 Replies

10. Red Hat

Regarding Network Interface Card

Dear All , While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card. Pl find the below alert. Network Interface Card performance for NIC:eth1 has exceeded Major threshold. Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
dhcpmgr(1M)						  System Administration Commands					       dhcpmgr(1M)

NAME
dhcpmgr - graphical interface for managing DHCP service SYNOPSIS
/usr/sadm/admin/bin/dhcpmgr DESCRIPTION
dhcpmgr is a graphical user interface which enables you to manage the Dynamic Host Configuration Protocol (DHCP) service on the local sys- tem. It performs the functions of the dhcpconfig, dhtadm, and pntadm command line utilities. You must be root to use dhcpmgr. The dhcpmgr Help, available from the Help menu, contains detailed information about using the tool. USAGE
You can perform the following tasks using dhcpmgr: Configure DHCP service Use dhcpmgr to configure the DHCP daemon as a DHCP server, and select the data store to use for storing network configuration tables.. Configure BOOTP relay service Use dhcpmgr to configure the DHCP daemon as a BOOTP relay. Manage DHCP or BOOTP relay service Use dhcpmgr to start, stop, enable, disable or unconfigure the DHCP service or BOOTP relay service, or change DHCP server parameters. Manage DHCP addresses Use dhcpmgr to add, modify, or delete IP addresses leased by the DHCP service. Manage DHCP macros Use dhcpmgr to add, modify or delete macros used to supply configuration parameters to DHCP clients. Manage DHCP options Use dhcpmgr to add, modify or delete options used to define parameters deliverable through DHCP. Convert to a new DHCP data store Use dhcpmgr to configure the DHCP server to use a different data store, and convert the DHCP data to the format used by the new data store. Move DHCP data to another server Use dhcpmgr to export data from one Solaris DHCP server and import data onto another Solaris DHCP server. EXIT STATUS
The following exit values are returned: 0 Successful completion. non-zero An error occurred. ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWdhcm | +-----------------------------+-----------------------------+ |Interface Stability |Evolving | +-----------------------------+-----------------------------+ SEE ALSO
dhcpconfig(1M), dhtadm(1M), pntadm(1M), in.dhcpd(1M), dhcpsvc.conf(4), dhcp_network(4), dhcptab(4), attributes(5), dhcp(5), dhcp_modules(5) Solaris DHCP Service Developer's Guide System Administration Guide: IP Services SunOS 5.10 13 Mar 2001 dhcpmgr(1M)
All times are GMT -4. The time now is 01:22 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy