Sponsored Content
Full Discussion: Replace failed drive in pool
Operating Systems Solaris Replace failed drive in pool Post 302929611 by hicksd8 on Tuesday 23rd of December 2014 11:15:29 AM
Old 12-23-2014
Hmmmm, no LBA value on the disk labels, that is unusual.

However, you can see from your prtvtoc's in post#1 that your new disk is smaller than the old one.

Partition 2 (which on Sun describes the whole disk) sector count says:
Code:
old 585912500
new 585865020

Some new filesystems will reserve some space (eg, 100MB) on the drives to manage such a situation but if your filesystem has used the full capacity then there's no alternative but to get one with the same, or more, sectors (LBA's).

Last edited by rbatte1; 12-23-2014 at 01:23 PM..
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Replace the tape backup drive

Please help me!!!. I am new to Unix and I have to replace the tape backup drive. Originally the system had an IBM tape drive (Rhomat) that is damged. I changed it and installed a dat drive HP 5000+. The hardware recognize the drive, the diagnostics if OK. But when I try to install the operating... (3 Replies)
Discussion started by: allaite2
3 Replies

2. Shell Programming and Scripting

Failed to replace string with "sed"

Hi folks, I have the following configuration file: tofu:/tmp # cat bitbandConfig.properties maestroIp=10.10.10.10 maestroPort=2020 adminPlayPath=<Streaming Agent IP>:2021/streamingGateway/GetPlayList ###This part should not be changed### adminPlayVODProtocol=http username=iptv... (7 Replies)
Discussion started by: nir_s
7 Replies

3. AIX

Replace a Failed Root Disk in AIX

My root disk is failed and how to replace the root disk in AIX. Can u give a detailed explanation in step wise. Pls give the answer taking different scenarios. Regards Praveen (1 Reply)
Discussion started by: chinnu_mulakala
1 Replies

4. UNIX for Dummies Questions & Answers

Replace Drive

Any help appreciated Sco Unix Ver 5.0+ Have 2 90 gig mirrored drives Can these be replaced with any similar drive? Can one just be replaced and will the mirror rebuild on it and then allow reboot on it ---then replace 2nd drive? Thanks pb (3 Replies)
Discussion started by: paul1730
3 Replies

5. OS X (Apple)

Failed Drive

I am trying to recover data off a drive that failed in my iMac. Apple returned the drive to me and I purchased a hard drive enclosure. I have been doing research on prices for data recovery services, way too expensive. I seen some links using Unix DD commands in the terminal none of which worked.... (6 Replies)
Discussion started by: KJ1906
6 Replies

6. Infrastructure Monitoring

zfs - migrate from pool to pool

Here are the details. cnjr-opennms>root$ zfs list NAME USED AVAIL REFER MOUNTPOINT openpool 20.6G 46.3G 35.5K /openpool openpool/ROOT 15.4G 46.3G 18K legacy openpool/ROOT/rds 15.4G 46.3G 15.3G / openpool/ROOT/rds/var 102M ... (3 Replies)
Discussion started by: pupp
3 Replies

7. Solaris

How to replace failed disk?

Dear all Please can any one explain me how to replace failed disk in Solaris 10. Please tell me the step by step procedure. (9 Replies)
Discussion started by: suneelieg
9 Replies

8. Solaris

Cannot remove and replace failed disk

-bash-3.00# zpool detach zonepool c1t1d0 cannot detach c1t1d0: only applicable to mirror and replacing vdevs -bash-3.00# zpool remove zonepool c1t1d0 cannot remove c1t1d0: only inactive hot spares, cache, top-level, or log devices can be removed -bash-3.00# zpool offline zonepool c1t1d0... (3 Replies)
Discussion started by: LittleLebowski
3 Replies

9. AIX

RAID 10 Failed Drive Swap

I am new to the AIX operating system and am seeking out some advice. We recently have had a drive go bad on our AIX server that is in a RAID 10 array. We have a replacement on the way. I was wondering what the correct steps are to swap out this drive. Does the server need to be powered off? Or can... (5 Replies)
Discussion started by: mpeter05
5 Replies

10. AIX

Stale PPs in AIX, failed disks.. how to replace?

I have a AIX 7.1 system that has 3 failed disks, 1 in rootvg and 2 in vg_usr1. Here is the output of lspv. # lspv hdisk0 00044d4dfbb11575 vg_usr1 active hdisk1 0000150179158027 vg_usr1 active hdisk2 ... (11 Replies)
Discussion started by: c3rb3rus
11 Replies
All times are GMT -4. The time now is 08:32 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy