12-18-2014
Quote:
Originally Posted by
hicksd8
When it says "drive too small" it almost certainly means just that.
Drive manufacturers have a habit of using the same part number/model number for slightly different size drives to give their product line some resemblance of continuity.
If you can, put both drives on a desk and, hopefully, both disk drives will have a LBA (logical block capacity) on their labels. These are big numbers but compare them. Chances are that the number of LBA's on the new drive is less than the number of LBA's on the old drive. Solaris won't like that since when the old drive was configured Solaris used the full available capacity.
You need a drive with the same or greater number of LBAs which will be the number that Solaris is interested in. The new drive can be the same number of LBAs as the old drive or any number greater but NOT a single LBA smaller.
Hope that helps.
What's prtvtoc show for the working drive in the mirror?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Please help me!!!. I am new to Unix and I have to replace the tape backup drive. Originally the system had an IBM tape drive (Rhomat) that is damged. I changed it and installed a dat drive HP 5000+. The hardware recognize the drive, the diagnostics if OK. But when I try to install the operating... (3 Replies)
Discussion started by: allaite2
3 Replies
2. Shell Programming and Scripting
Hi folks,
I have the following configuration file:
tofu:/tmp # cat bitbandConfig.properties
maestroIp=10.10.10.10
maestroPort=2020
adminPlayPath=<Streaming Agent IP>:2021/streamingGateway/GetPlayList
###This part should not be changed###
adminPlayVODProtocol=http
username=iptv... (7 Replies)
Discussion started by: nir_s
7 Replies
3. AIX
My root disk is failed and how to replace the root disk in AIX.
Can u give a detailed explanation in step wise.
Pls give the answer taking different scenarios.
Regards
Praveen (1 Reply)
Discussion started by: chinnu_mulakala
1 Replies
4. UNIX for Dummies Questions & Answers
Any help appreciated
Sco Unix Ver 5.0+
Have 2 90 gig mirrored drives
Can these be replaced with any similar drive?
Can one just be replaced and will the mirror rebuild on it and then allow reboot on it ---then replace 2nd drive?
Thanks
pb (3 Replies)
Discussion started by: paul1730
3 Replies
5. OS X (Apple)
I am trying to recover data off a drive that failed in my iMac. Apple returned the drive to me and I purchased a hard drive enclosure. I have been doing research on prices for data recovery services, way too expensive. I seen some links using Unix DD commands in the terminal none of which worked.... (6 Replies)
Discussion started by: KJ1906
6 Replies
6. Infrastructure Monitoring
Here are the details.
cnjr-opennms>root$ zfs list
NAME USED AVAIL REFER MOUNTPOINT
openpool 20.6G 46.3G 35.5K /openpool
openpool/ROOT 15.4G 46.3G 18K legacy
openpool/ROOT/rds 15.4G 46.3G 15.3G /
openpool/ROOT/rds/var 102M ... (3 Replies)
Discussion started by: pupp
3 Replies
7. Solaris
Dear all
Please can any one explain me how to replace failed disk in Solaris 10.
Please tell me the step by step procedure. (9 Replies)
Discussion started by: suneelieg
9 Replies
8. Solaris
-bash-3.00# zpool detach zonepool c1t1d0
cannot detach c1t1d0: only applicable to mirror and replacing vdevs
-bash-3.00# zpool remove zonepool c1t1d0
cannot remove c1t1d0: only inactive hot spares, cache, top-level, or log devices can be removed
-bash-3.00# zpool offline zonepool c1t1d0... (3 Replies)
Discussion started by: LittleLebowski
3 Replies
9. AIX
I am new to the AIX operating system and am seeking out some advice. We recently have had a drive go bad on our AIX server that is in a RAID 10 array. We have a replacement on the way. I was wondering what the correct steps are to swap out this drive. Does the server need to be powered off? Or can... (5 Replies)
Discussion started by: mpeter05
5 Replies
10. AIX
I have a AIX 7.1 system that has 3 failed disks, 1 in rootvg and 2 in vg_usr1.
Here is the output of lspv.
# lspv
hdisk0 00044d4dfbb11575 vg_usr1 active
hdisk1 0000150179158027 vg_usr1 active
hdisk2 ... (11 Replies)
Discussion started by: c3rb3rus
11 Replies
LEARN ABOUT FREEBSD
mlxcontrol
MLXCONTROL(8) BSD System Manager's Manual MLXCONTROL(8)
NAME
mlxcontrol -- Mylex DAC-family RAID management utility
SYNOPSIS
mlxcontrol <command> [args]
mlxcontrol status [-qv] [drive]
mlxcontrol rescan controller [controller ...]
mlxcontrol detach drive [drive ...]
mlxcontrol detach -a
mlxcontrol check drive
mlxcontrol config controller
mlxcontrol help command
DESCRIPTION
The mlxcontrol utility provides status monitoring and management functions for devices attached to the mlx(4) driver.
Controller names are of the form "mlxN" where N is the unit number of the controller. Drive names are of the form "mlxdN" where N is the
unit number of the drive. Do not specify the path to a device node.
status Print the status of controllers and system drives. If one or more drives are specified, only print information about these drives,
otherwise print information about all controllers and drives in the system. With the -v flag, display much more verbose informa-
tion. With the -q flag, do not print any output. This command returns 0 if all drives tested are online, 1 if one or more drives
are critical and 2 if one or more are offline.
rescan Rescan one or more controllers for non-attached system drives (e.g. drives that have been detached or created subsequent to driver
initialisation). If the -a flag is supplied, rescan all controllers in the system.
detach Detach one or more system drives. Drives must be unmounted and not opened by any other utility for this command to succeed. If the
-a flag is supplied, detach all system drives from the nominated controller.
check Initiate a consistency check and repair pass on a redundant system drive (e.g. RAID1 or RAID5). The controller will scan the system
drive and repair any inconsistencies. This command returns immediately; use the status command to monitor the progress of the
check.
rebuild Requires two arguments, controller and physdrive as specified in the output of the status command. All system drives using space on
the physical drive physdrive are rebuilt, reconstructing all data on the drive. Note that each controller can only perform one
rebuild at a time. This command returns immediately; use the status command to monitor the progress of the rebuild.
config Print the current configuration from the nominated controller. This command will be updated to allow addition/deletion of system
drives from a configuration in a future release.
help Print usage information for command.
AUTHORS
The mlxcontrol utility was written by Michael Smith <msmith@FreeBSD.org>.
BUGS
The config command does not yet support modifying system drive configuration.
Error log extraction is not yet supported.
BSD
April 10, 2000 BSD