11-06-2014
Yes it is a HP hardware. DL380
9 More Discussions You Might Find Interesting
1. Solaris
I setup RSC on a 280R using the network connection. Unfortunately, I am unable to telnet to this card and I was wondering if there was a way to test the link from the rsc card. Here is my rsc configuration:
machine1:/tmp/rsc# /usr/platform/SUNW,Sun-Fire-280R/rsc/rscadm show
page_enabled="false"... (0 Replies)
Discussion started by: dangral
0 Replies
2. UNIX for Dummies Questions & Answers
My system info is show below:-
#uname -a
SunOS qfserver 5.8 Generic_117350-29 sun4u sparc SUNW,Sun-Blade-2500
and I have two network card as shown below:-
#ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0:... (1 Reply)
Discussion started by: sarifudin
1 Replies
3. AIX
Hello,
I need "devices.common.IBM.ml 1.4.0.0 C F Multi Link Interface Runtime" to be installed on my machine.
I need it for two SAN cards to work correctly.
Where do I get it ?
thanks
Vilius (1 Reply)
Discussion started by: vilius
1 Replies
4. Red Hat
Hi
I have installed OEL 4 on my dell XPS laptop. But when i connect the LAN cable and try to acesss internet. it does not work. the led's in the port do not blink when i plug in the cable .do i need some drivers please suggest.
Thanks
Ankur (2 Replies)
Discussion started by: ankurk
2 Replies
5. IP Networking
Hello,
I've been using mode 4 with four slaves, however looking at ifconfig showed that the traffic was not balanced correctly between the interfaces, the outgoing traffic has been alot higher on the last slave.
Example:
eth0 RX 123.2 GiB TX 22.5 GiB
eth1 RX 84.8 GiB TX 8.3 GiB
eth2... (3 Replies)
Discussion started by: TehOne
3 Replies
6. Solaris
I have system which is using a lot of bandwidth and this is not a big problem,
but how do you troubleshoot this issue?
How can I find out which connections are made for one interface card,
there are about 5 on this system and I can see how much traffic is going through one interface, but I need... (5 Replies)
Discussion started by: misterx12345
5 Replies
7. Solaris
Hi All
I am facing an issue with our new solaris machine.
in /var/adm/messages
root@Prod-App1:/var/tmp#
root@Prod-App1:/var/tmp#
root@Prod-App1:/var/tmp# cat /var/adm//messages
Apr 20 03:10:01 Prod-App1 syslogd: line 25: WARNING: loghost could not be resolved
Apr 20 08:24:18 Prod-App1... (0 Replies)
Discussion started by: javeedkaleem
0 Replies
8. Red Hat
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
9. Solaris
I'm looking for driver for SunSAI/P 3.0 (Serial Asynchronous Interface) card X2156A for Solaris. It used to be on sun-solve, but I fail to find it on the Oracle site. Any help would be very appreciated! (1 Reply)
Discussion started by: Ira28
1 Replies
LEARN ABOUT HPUX
io_redirect_dsf
io_redirect_dsf(1M) io_redirect_dsf(1M)
NAME
io_redirect_dsf - redirect the persistent device special file from one device to a different device
SYNOPSIS
old_hw_path new_hw_path
old_dsf new_dsf
DESCRIPTION
The command reassigns a persistent device special file (DSF) to a new device when both devices belong to the same class. If the new device
does not already exist, before reassigning it you must create the DSF by running either or (see insf(1M) and mksf(1M)).
In the first form, the command accepts as input the lun hardware paths of the device to be replaced and the new device. In the second
form, the command accepts as input the persistent DSFs of the device to be replaced and the new device.
Note: The device is inaccessible while the redirection is taking place.
Options
recognizes the following options:
Specify the hardware path of the device that is being replaced.
returns an error if old_hw_path is not a lun hardware path.
Specify the hardware path of the new device.
returns an error if new_hw_path is not a lun hardware path.
Specify the device special file of the device that is being replaced.
returns an error if old_dsf is not a persistent DSF.
Specify the device special file of the new device.
returns an error if new_dsf is not a persistent DSF.
RETURN VALUE
Exit values are:
Successful completion.
An error condition occurred.
EXAMPLES
Redirect the DSF with the hardware path at to point to the hardware path at Both disks belong to the class.
Redirect the DSF to point to the device with DSF Both DSFs represent devices that belong to the class
WARNINGS
You must be superuser to execute the command.
SEE ALSO
insf(1M), mksf(1M), intro(7).
io_redirect_dsf(1M)