10-30-2014
Firstly, this seems to be a RedHat issue? Posting on the correct forum will mean that the right experts are much more likely to see it.
NOTE TO MODERATOR: Please move this to RedHat.
Also, have you searched the RedHat forum for this issue? I feel sure I've seen this discussed before (on the RedHat forum).
This User Gave Thanks to hicksd8 For This Post:
9 More Discussions You Might Find Interesting
1. Solaris
I setup RSC on a 280R using the network connection. Unfortunately, I am unable to telnet to this card and I was wondering if there was a way to test the link from the rsc card. Here is my rsc configuration:
machine1:/tmp/rsc# /usr/platform/SUNW,Sun-Fire-280R/rsc/rscadm show
page_enabled="false"... (0 Replies)
Discussion started by: dangral
0 Replies
2. UNIX for Dummies Questions & Answers
My system info is show below:-
#uname -a
SunOS qfserver 5.8 Generic_117350-29 sun4u sparc SUNW,Sun-Blade-2500
and I have two network card as shown below:-
#ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0:... (1 Reply)
Discussion started by: sarifudin
1 Replies
3. AIX
Hello,
I need "devices.common.IBM.ml 1.4.0.0 C F Multi Link Interface Runtime" to be installed on my machine.
I need it for two SAN cards to work correctly.
Where do I get it ?
thanks
Vilius (1 Reply)
Discussion started by: vilius
1 Replies
4. Red Hat
Hi
I have installed OEL 4 on my dell XPS laptop. But when i connect the LAN cable and try to acesss internet. it does not work. the led's in the port do not blink when i plug in the cable .do i need some drivers please suggest.
Thanks
Ankur (2 Replies)
Discussion started by: ankurk
2 Replies
5. IP Networking
Hello,
I've been using mode 4 with four slaves, however looking at ifconfig showed that the traffic was not balanced correctly between the interfaces, the outgoing traffic has been alot higher on the last slave.
Example:
eth0 RX 123.2 GiB TX 22.5 GiB
eth1 RX 84.8 GiB TX 8.3 GiB
eth2... (3 Replies)
Discussion started by: TehOne
3 Replies
6. Solaris
I have system which is using a lot of bandwidth and this is not a big problem,
but how do you troubleshoot this issue?
How can I find out which connections are made for one interface card,
there are about 5 on this system and I can see how much traffic is going through one interface, but I need... (5 Replies)
Discussion started by: misterx12345
5 Replies
7. Solaris
Hi All
I am facing an issue with our new solaris machine.
in /var/adm/messages
root@Prod-App1:/var/tmp#
root@Prod-App1:/var/tmp#
root@Prod-App1:/var/tmp# cat /var/adm//messages
Apr 20 03:10:01 Prod-App1 syslogd: line 25: WARNING: loghost could not be resolved
Apr 20 08:24:18 Prod-App1... (0 Replies)
Discussion started by: javeedkaleem
0 Replies
8. Red Hat
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
9. Solaris
I'm looking for driver for SunSAI/P 3.0 (Serial Asynchronous Interface) card X2156A for Solaris. It used to be on sun-solve, but I fail to find it on the Oracle site. Any help would be very appreciated! (1 Reply)
Discussion started by: Ira28
1 Replies
DAIC(4) BSD Kernel Interfaces Manual DAIC(4)
NAME
daic -- isdn4bsd driver for EICON.Diehl active ISDN cards
SYNOPSIS
daic0 at isa? iomem 0xd8000 irq 10
DESCRIPTION
The daic driver supports the old Diehl active cards: S, SX, SXn, SCOM and QUADRO.
For a QUADRO card, the driver will detect the board type and use all four ports, each attached as a controller of its own to the isdn4bsd
system, which can be listed using the daicctl utility.
The daic driver interfaces the ISDN card to the ISDN4BSD kernel subsystem. All lower layer ISDN control is handled by the card. This should
allow you to run any national ISDN protocol delivered by EICON.Diehl for your card, but the driver has only been tested with the DSS1 proto-
col and some parts of the cards interface are ISDN protocol dependent.
The daic driver is written to conform to the software interface documented by Diehl in their ISDN-Karten Benutzerhandbuch from 1992.
MICROCODE DOWNLOAD
Every active card needs its own operating software before it can work. You have to download this to the card before using it with isdn4bsd.
Use the daicctl utility to do this, i.e. call daicctl -d te_etsi.sx 1 to download the file te_etsi.sx to controller number 1. Use daicctl -l
to list all available controllers (and ports). You have to select the correct ISDN protocol file for your ISDN interface, see the Diehl docu-
mentation for details.
The cards bootstrap process involves another file, which is independent of the card type you use and the protocol you run. It is called
download.bin in current versions of the Diehl software distribution and has to be copied to the kernel compile directory under
dev/microcode/daic and converted into a header file used when compiling the kernel by running make in that directory. Your kernel compile
will fail and remind you of this if you forget to do this. Due to copyright restrictions we cannot distribute the driver with this file inte-
grated. But if you own a card, you do have the file (or can get it from the Diehl web server).
SEE ALSO
daicctl(1)
BUGS
The driver is not yet finished.
BSD
January 30, 1998 BSD