Sponsored Content
Operating Systems Linux Red Hat Interface card link goes down and recovers frequently Post 302923102 by hicksd8 on Thursday 30th of October 2014 10:13:51 AM
Old 10-30-2014
Firstly, this seems to be a RedHat issue? Posting on the correct forum will mean that the right experts are much more likely to see it.

NOTE TO MODERATOR: Please move this to RedHat.

Also, have you searched the RedHat forum for this issue? I feel sure I've seen this discussed before (on the RedHat forum).
This User Gave Thanks to hicksd8 For This Post:
 

9 More Discussions You Might Find Interesting

1. Solaris

testing link on RSC card

I setup RSC on a 280R using the network connection. Unfortunately, I am unable to telnet to this card and I was wondering if there was a way to test the link from the rsc card. Here is my rsc configuration: machine1:/tmp/rsc# /usr/platform/SUNW,Sun-Fire-280R/rsc/rscadm show page_enabled="false"... (0 Replies)
Discussion started by: dangral
0 Replies

2. UNIX for Dummies Questions & Answers

Multi Network card interface problem

My system info is show below:- #uname -a SunOS qfserver 5.8 Generic_117350-29 sun4u sparc SUNW,Sun-Blade-2500 and I have two network card as shown below:- #ifconfig -a lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 bge0:... (1 Reply)
Discussion started by: sarifudin
1 Replies

3. AIX

Multi Link Interface Runtime - where to download ?

Hello, I need "devices.common.IBM.ml 1.4.0.0 C F Multi Link Interface Runtime" to be installed on my machine. I need it for two SAN cards to work correctly. Where do I get it ? thanks Vilius (1 Reply)
Discussion started by: vilius
1 Replies

4. Red Hat

How to configure network interface card in OEL.

Hi I have installed OEL 4 on my dell XPS laptop. But when i connect the LAN cable and try to acesss internet. it does not work. the led's in the port do not blink when i plug in the cable .do i need some drivers please suggest. Thanks Ankur (2 Replies)
Discussion started by: ankurk
2 Replies

5. IP Networking

Interface bonding / Link aggregation (Multiple)

Hello, I've been using mode 4 with four slaves, however looking at ifconfig showed that the traffic was not balanced correctly between the interfaces, the outgoing traffic has been alot higher on the last slave. Example: eth0 RX 123.2 GiB TX 22.5 GiB eth1 RX 84.8 GiB TX 8.3 GiB eth2... (3 Replies)
Discussion started by: TehOne
3 Replies

6. Solaris

Interface card using a lot of bandwith

I have system which is using a lot of bandwidth and this is not a big problem, but how do you troubleshoot this issue? How can I find out which connections are made for one interface card, there are about 5 on this system and I can see how much traffic is going through one interface, but I need... (5 Replies)
Discussion started by: misterx12345
5 Replies

7. Solaris

/var/adm/messages (interface turned off/restored) and link up & link down message.

Hi All I am facing an issue with our new solaris machine. in /var/adm/messages root@Prod-App1:/var/tmp# root@Prod-App1:/var/tmp# root@Prod-App1:/var/tmp# cat /var/adm//messages Apr 20 03:10:01 Prod-App1 syslogd: line 25: WARNING: loghost could not be resolved Apr 20 08:24:18 Prod-App1... (0 Replies)
Discussion started by: javeedkaleem
0 Replies

8. Red Hat

Regarding Network Interface Card

Dear All , While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card. Pl find the below alert. Network Interface Card performance for NIC:eth1 has exceeded Major threshold. Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies

9. Solaris

Looking for driver for SunSAI/P 3.0 (Serial Asynchronous Interface) card X2156A

I'm looking for driver for SunSAI/P 3.0 (Serial Asynchronous Interface) card X2156A for Solaris. It used to be on sun-solve, but I fail to find it on the Oracle site. Any help would be very appreciated! (1 Reply)
Discussion started by: Ira28
1 Replies
ALCC(1) 							  aMule utilities							   ALCC(1)

NAME
alcc - text based eD2k links calculator for aMule SYNOPSIS
alcc [-p] [-v] <inputfiles_list> alcc [-h] DESCRIPTION
Compute the eD2k links of all the input files given in the <inputfiles_list> (There can be one or more files). [ -p, --parthashes ] Compute and add part hashes to the computed eD2k links. [ -h, --help ] Prints a short usage description. [ -v, --verbose ] Be verbose - show also calculation steps. REPORTING BUGS
Please report bugs either on our forum (http://forum.amule.org/), or in our bugtracker (http://bugs.amule.org/). Please do not report bugs in e-mail, neither to our mailing list nor directly to any team member. COPYRIGHT
aMule and all of its related utilities are distributed under the GNU General Public License. SEE ALSO
alc(1), amuled(1), amulecmd(1), amuleweb(1), cas(1), ed2k(1), wxcas(1), xas(1) AUTHOR
This manpage was written by Vollstrecker <amule@vollstreckernet.de> aMule eD2k links calculator November 2011 ALCC(1)
All times are GMT -4. The time now is 01:06 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy