The only difference between eth4 and eth5 and the others (eth0-eth3)is that they are set to ONBOOT no, and their MAC addresses don't correspond to the actual physical MAC addresses (obviously).
---------- Post updated at 09:09 AM ---------- Previous update was at 08:57 AM ----------
In other words, its quite obvious that the former employee did something to configure these virtual interfaces for some reason, but how do I go about figuring out what?
Sorry I come from a Windows background, so outside of the normal everyday stuff a lot of this is still foreign to me in Linux.
Last edited by Corona688; 10-23-2014 at 01:25 PM..
Hello,
I would like to know if there is a command or any configuration file to find and differentiate the Virtual IP Addresses (of the Cluster Resource Group) and the IP Address of the Cluster Node. I observe that the ifconfig -a command returns all the IP addresses configured on the ... (1 Reply)
Do we have any Virtual Data Center software as we have Virtual Machine?
I want to practice everything of Solaris practically but i don't have resources like data center which includes Servers, Data storages, switches, and other things. (2 Replies)
Hello All,
I have a requirement to add multiple virtual interfaces on a non-global zone (Solaris 10). The global zone is a 2 node Veritas Cluster Server. So, my question is do we have to make any modifications to the cluster config (which I think should not be the case)? Can anyone help with me... (11 Replies)
Not really a newbie, but I have a strange problem and I'm not sure how to further troubleshoot it.
I have to log out of a virtual terminal by typing exit, then exit again as in:
woodnt@toshiba-laptop ~ $ exit
logout
woodnt@toshiba-laptop ~ $ exit
logout
I DON'T have to do this when I'm... (1 Reply)
My setup consists of a hardware node, which hosts several virtual machines (OpenVZ, to be precise). The hardware node has two network interfaces (<ifA>, <ifB>) connected to different subnets (<networkA>, <networkB>). I want to route the traffic of certain VEs over <ifB> while routing the other VEs... (0 Replies)
Trying to set or modify the randomly set hostID of a Solaris 10 virtual/guest machine that I installed on a Windows-XP host machine (using Virtual Box 4.1.12).
I was able to set/modify the hostname of the Solaris 10 virtual/guest machine during installation as well as via the Virtual Box... (4 Replies)
Hi Al,
In course of understanding networking in Solaris, I have these doubts on Interfaces. Please clarify me. I have done fair research in this site and others but could not be clarified.
1. In the "ifconfig -a" command, I see many interfaces and their configurations. But I see many... (1 Reply)
Hi All,
Is there any way I can prioritize my VMs when there is resource crunch in host machine so that some VMs will be allocated more vcpu, more memory than other VMs in kvm/qemu hypervisor based virtual machines?
Lets say in my cloud environment my Ubuntu 16 compute hosts are running some... (0 Replies)
Hi,
I have RH Linux system on which we have a 10Gb nic card that we want to configure multiple Virtual interfaces that are all tagged on the switch side.
Here is what I am trying to do, I want to have clients from different vlans that are truncked to be able to communicate with my RHEL... (1 Reply)
Discussion started by: new2prog
1 Replies
LEARN ABOUT DEBIAN
vlan-interfaces
VLAN-INTERFACES(5) File formats VLAN-INTERFACES(5)NAME
/etc/network/interfaces (vlan) - vlan extensions for the interfaces(5) file format
DESCRIPTION
/etc/network/interfaces contains network interface configuration information for the ifup(8) and ifdown(8) commands. This manpage
describes the vlan extensions to the standard interfaces(5) file format.
Primary extensions exist to make and destroy vlan interfaces, secondary extensions exist for ipv4 interface manipulation which are gener-
ally needed when using (a lot of) vlans.
VLAN CREATION
Vlan interface definitions exist of the vlan interface name, and an optional 'raw-device' parameter. Vlan interfaces are numbered 1 to
4095. You have the option to have interface names zero-padded to 4 numbers, or just the plain digits without leading zero. The following
example shows four ways to create a vlan with id 1 on interface eth0. They all result in different names.
iface eth0.1 inet static
address 192.168.1.1
netmask 255.255.255.0
iface vlan1 inet static
vlan-raw-device eth0
address 192.168.1.1
netmask 255.255.255.0
iface eth0.0001 inet static
address 192.168.1.1
netmask 255.255.255.0
iface vlan0001 inet static
vlan-raw-device eth0
address 192.168.1.1
netmask 255.255.255.0
# We don't have br support out of the box
iface br0.2 inet static
vlan-raw-device br0
address 192.168.1.1
netmask 255.255.255.0
# Aliases are ignored
iface br0.2:1 inet static
address 192.168.1.1
netmask 255.255.255.255
EXTRA IFACE OPTIONS
Usually someone who uses vlans also wants to do some other manipulations with the ip stack or interface.
vlan-raw-device devicename
Indicates the device to create the vlan on. This is ignored when the devicename is part of the vlan interface name.
ip-proxy-arp 0|1
Turn proxy-arp off or on for this specific interface. This also works on plain ethernet like devices.
ip-rp-filter 0|1|2
Set the return path filter for this specific interface. This also works on plain ethernet like devices.
hw-mac-address mac-address
This sets the mac address of the interface before bringing it up. This works on any device that allows setting the hardware address
with the ip command.
AUTHOR
This manpage was adapted from interfaces(5) by Ard van Breemen <ard@kwaak.net>
SEE ALSO vconfig(8)interfaces(5)vlan September 30 2007 VLAN-INTERFACES(5)