10-22-2014
Thanks wisecracker -
Now I have the loopback plug...
No matter how the hardware and software flow control are set..IT WORKS!!!
What is the next step?
10 More Discussions You Might Find Interesting
1. Linux
I think my serial port(on board) is not working ......
because when I am running same code on two machines its working good....but when my system comes into picture ....it doesnt show any output comming from serial port..........
can anybody tell me how to configure my serial port.........or to... (16 Replies)
Discussion started by: arunchaudhary19
16 Replies
2. Solaris
Hi,
I am working with solaris 9,SUN-Blade-100 and I want to communicate with the Serial port.To check whether the port is working or not.I write code and when I execute the file,then I got the output--
According to this,serial port is not found.can anyone please tell me how to configure the... (1 Reply)
Discussion started by: smartgupta
1 Replies
3. Programming
I have a need to determine when a string has been completely sent via a serial port from a standard 'C' application. The code is as follows:
SerialPort_Send = open (pPortString, O_WRONLY | O_NOCTTY | O_NONBLOCK);
write (SerialPort_Send, pCommandString, strlen (pCommandString));
... (2 Replies)
Discussion started by: ExDes
2 Replies
4. AIX
Hi,
How can i configure my modem in AIX thru serial port (sa0-->tty0)
I have two port serial card configured as sa0
I created tty1 which port is tty0 and which port is tty1 how can i know?? (1 Reply)
Discussion started by: pchangba
1 Replies
5. UNIX for Dummies Questions & Answers
A neighbour's Ubuntu 10.04 machine has five serial ports, one on the motherboard and four on a PCI card. However, only four cards are showing:
# dmesg | grep tty
console enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
... (2 Replies)
Discussion started by: dotancohen
2 Replies
6. Shell Programming and Scripting
Hi,
I have a external board connected to my serial port. I need to execute "shutdown -r now" command when system boot up. When system boots up it requires a username ans password. Then I need to run my command. I can use rc script but that is rebooting system before it asks for username and... (0 Replies)
Discussion started by: charlie.arya
0 Replies
7. Solaris
Hi Everyone,
In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected... (3 Replies)
Discussion started by: bobby320
3 Replies
8. Shell Programming and Scripting
hello all,
please any one can provide me the shell script to write data to /dev/ttyS1
and read responce from /dev/ttyS1 and compare the responce to some string ..
thnxx
---------- Post updated at 03:35 PM ---------- Previous update was at 11:46 AM ----------
any body help me..
how do i... (1 Reply)
Discussion started by: yashwantkumar
1 Replies
9. Web Development
I need to set a serial port to 9600 7E1. How do I accomplish this?
I've tried every combination, with no luck. (6 Replies)
Discussion started by: Meow613
6 Replies
10. Solaris
Hello,
I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build.
The first part is what confuses me -the cabling.
I am coming from a Windows machine (w/appropriate... (5 Replies)
Discussion started by: joboy
5 Replies
uusend(1) General Commands Manual uusend(1)
NAME
uusend - Sends a file to a remote host
SYNOPSIS
uusend [-m mode] local_file system1! system2! ...!remote_file
The uusend command sends a file to a given location on a remote system.
OPTIONS
Specifies that the mode of the file on the remote system be taken from the octal number given. If this flag is not specified, the mode of
the input file is used.
DESCRIPTION
The remote system does not need to be directly connected to the local system, but a chain of uucp links needs to connect the two system.
ENVIRONMENT VARIABLES
The following environment variables affect the execution of uusend: [Tru64 UNIX] Specifies the flow control used on the connection. Per-
mitted values are: HW (hardware), SW (software), HSW (hardware and software), and NONE. The uugetty on the remote system must also use the
same flow control. Specifies the amount of time (in seconds) for uucico to try to establish a connection before it times out. A value of
0 (zero) indicates an unlimited amount of time.
SEE ALSO
Commands: ct(1), cu(1), tip(1), uucico(8), uucleanup(8), uucp(1), uuencode(1), uulog(1), uuname(1), uupick(1), uusched(8), uustat(1),
uuto(1), uux(1)
uusend(1)