i found out that there is the command brctl. it was in another directory which was not in the path. the output is the following.
again the output of route is
ip route show delivers
ip link show delivers
i think i need to remove br0 and bridge wan0 to eth1. but i am not sure.
again wan0 is the ehternet port which is connected to my homenetwork (switch).
if i try to remove the interface from the bridge br0 i loose my ssh-connection to the router. so this is no option. removing the bridge does not work because it is denied by brctl. i am a little stuck right now because of my limited knowledge to ip.
i repeat myself but with the recent permanten configuration the internal sip-telephony which needs access to internet works. for a solution i need a simple command that i can enter from the console to use the lan2-4 ports.
any ideas ? thx in advance.
Last edited by gencaslan; 10-11-2014 at 07:49 PM..
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
My setup consists of a hardware node, which hosts several virtual machines (OpenVZ, to be precise). The hardware node has two network interfaces (<ifA>, <ifB>) connected to different subnets (<networkA>, <networkB>). I want to route the traffic of certain VEs over <ifB> while routing the other VEs... (0 Replies)
Dear Sir
I am a newbie in the world of IP telephony. I have been working with Asterisk PBX (SIP) and Cisco Call Manager (MGCP) but now I am learning on how to work GNUGK for H.323 Gatekeeper.
I am having a problem, configuring static call routing on GNUGK
in the section
... (0 Replies)
Hello
i am configuring a debian lenny sever ,/etc/network/interfaces is modified so that eth1 takes a static IP address
then i save it wq!
then i restart the networking , /etc/init.d/networking restart .
but after reboot ,the file is reset ,note that the interfaces had by defauklt IPv6 address... (5 Replies)
Hi gurus of unix, I haved installed my openSolaris in a HP530,
Recently I use the following command
beadm destry opensolaris1
beadm destry opensolaris2
After That I reboot my Laptop.
Well when I go to my work I try to open my wireshark tool, but the option in GUI interface does not appear!!!... (2 Replies)
Hi,
I have two physical interfaces on a servers.
We have connected them to differerent subnets.
1) First interface:
10.158.49.87 to newtwork 10.158.49.0, its gateway is 10.158.49.1
(It is added as default gateway)
It is existing set up. It works well
2) Second interface:
... (1 Reply)
Hi .. we have two AIX 5.3 systems with a small client server app communicating over a TCP socket.
Box A has a single network interface where the server app (in Java) opens a well known port and waits for connections from Box B.
Box B has two network interfaces, X and Y. Interface X has the... (4 Replies)
Dear gurus of Linux / Unix.
I have a server, which I use to monitoring traffic, the problem that I find is when I run the following command:
probe:~ # sar -n DEV 1
I see that I one second appear info in some interface and in the other second no appear, I don't know what will be the... (0 Replies)
Dear friends
I use RedHat 6.5, which sets the gateway in the configuration file / etc / sysconfig / network as GATEWAY = 192.168.1.26, and the gateway in the configuration file / etc / sysconfig / network-scripts / ifcfg-eth11 as GATEWAY = 192.168.1.256. The two gateways are different.... (6 Replies)
Discussion started by: tanpeng
6 Replies
LEARN ABOUT XFREE86
ip-monitor
IP-MONITOR(8) Linux IP-MONITOR(8)NAME
ip-monitor, rtmon - state monitoring
SYNOPSIS
ip monitor [ all | OBJECT-LIST ] [ file FILENAME ] [ label ] [ all-nsid ] [ dev DEVICE ]
OPTIONS -t, -timestamp
Prints timestamp before the event message on the separated line in format:
Timestamp: <Day> <Month> <DD> <hh:mm:ss> <YYYY> <usecs> usec
<EVENT>
-ts, -tshort
Prints short timestamp before the event message on the same line in format:
[<YYYY>-<MM>-<DD>T<hh:mm:ss>.<ms>] <EVENT>
DESCRIPTION
The ip utility can monitor the state of devices, addresses and routes continuously. This option has a slightly different format. Namely,
the monitor command is the first in the command line and then the object list follows:
ip monitor [ all | OBJECT-LIST ] [ file FILENAME ] [ label ] [ all-nsid ] [ dev DEVICE ]
OBJECT-LIST is the list of object types that we want to monitor. It may contain link, address, route, mroute, prefix, neigh, netconf, rule
and nsid. If no file argument is given, ip opens RTNETLINK, listens on it and dumps state changes in the format described in previous sec-
tions.
If the label option is set, a prefix is displayed before each message to show the family of the message. For example:
[NEIGH]10.16.0.112 dev eth0 lladdr 00:04:23:df:2f:d0 REACHABLE [LINK]3: eth1: <BROADCAST,MULTICAST> mtu 1500 qdisc pfifo_fast state DOWN
group default
link/ether 52:54:00:12:34:57 brd ff:ff:ff:ff:ff:ff
If the all-nsid option is set, the program listens to all network namespaces that have a nsid assigned into the network namespace were the
program is running. A prefix is displayed to show the network namespace where the message originates. Example:
[nsid 0]10.16.0.112 dev eth0 lladdr 00:04:23:df:2f:d0 REACHABLE
If the file option is given, the program does not listen on RTNETLINK, but opens the given file, and dumps its contents. The file should
contain RTNETLINK messages saved in binary format. Such a file can be generated with the rtmon utility. This utility has a command line
syntax similar to ip monitor. Ideally, rtmon should be started before the first network configuration command is issued. F.e. if you
insert:
rtmon file /var/log/rtmon.log
in a startup script, you will be able to view the full history later.
Nevertheless, it is possible to start rtmon at any time. It prepends the history with the state snapshot dumped at the moment of starting.
If the dev option is given, the program prints only events related to this device.
SEE ALSO ip(8)AUTHOR
Original Manpage by Michail Litvak <mci@owl.openwall.com>
Manpage revised by Nicolas Dichtel <nicolas.dichtel@6wind.com>
iproute2 13 Dec 2012 IP-MONITOR(8)