i found out that there is the command brctl. it was in another directory which was not in the path. the output is the following.
again the output of route is
ip route show delivers
ip link show delivers
i think i need to remove br0 and bridge wan0 to eth1. but i am not sure.
again wan0 is the ehternet port which is connected to my homenetwork (switch).
if i try to remove the interface from the bridge br0 i loose my ssh-connection to the router. so this is no option. removing the bridge does not work because it is denied by brctl. i am a little stuck right now because of my limited knowledge to ip.
i repeat myself but with the recent permanten configuration the internal sip-telephony which needs access to internet works. for a solution i need a simple command that i can enter from the console to use the lan2-4 ports.
any ideas ? thx in advance.
Last edited by gencaslan; 10-11-2014 at 07:49 PM..
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
My setup consists of a hardware node, which hosts several virtual machines (OpenVZ, to be precise). The hardware node has two network interfaces (<ifA>, <ifB>) connected to different subnets (<networkA>, <networkB>). I want to route the traffic of certain VEs over <ifB> while routing the other VEs... (0 Replies)
Dear Sir
I am a newbie in the world of IP telephony. I have been working with Asterisk PBX (SIP) and Cisco Call Manager (MGCP) but now I am learning on how to work GNUGK for H.323 Gatekeeper.
I am having a problem, configuring static call routing on GNUGK
in the section
... (0 Replies)
Hello
i am configuring a debian lenny sever ,/etc/network/interfaces is modified so that eth1 takes a static IP address
then i save it wq!
then i restart the networking , /etc/init.d/networking restart .
but after reboot ,the file is reset ,note that the interfaces had by defauklt IPv6 address... (5 Replies)
Hi gurus of unix, I haved installed my openSolaris in a HP530,
Recently I use the following command
beadm destry opensolaris1
beadm destry opensolaris2
After That I reboot my Laptop.
Well when I go to my work I try to open my wireshark tool, but the option in GUI interface does not appear!!!... (2 Replies)
Hi,
I have two physical interfaces on a servers.
We have connected them to differerent subnets.
1) First interface:
10.158.49.87 to newtwork 10.158.49.0, its gateway is 10.158.49.1
(It is added as default gateway)
It is existing set up. It works well
2) Second interface:
... (1 Reply)
Hi .. we have two AIX 5.3 systems with a small client server app communicating over a TCP socket.
Box A has a single network interface where the server app (in Java) opens a well known port and waits for connections from Box B.
Box B has two network interfaces, X and Y. Interface X has the... (4 Replies)
Dear gurus of Linux / Unix.
I have a server, which I use to monitoring traffic, the problem that I find is when I run the following command:
probe:~ # sar -n DEV 1
I see that I one second appear info in some interface and in the other second no appear, I don't know what will be the... (0 Replies)
Dear friends
I use RedHat 6.5, which sets the gateway in the configuration file / etc / sysconfig / network as GATEWAY = 192.168.1.26, and the gateway in the configuration file / etc / sysconfig / network-scripts / ifcfg-eth11 as GATEWAY = 192.168.1.256. The two gateways are different.... (6 Replies)
Discussion started by: tanpeng
6 Replies
LEARN ABOUT DEBIAN
atalkd
ATALKD(8) Netatalk 2.2 ATALKD(8)NAME
atalkd - AppleTalk RTMP, NBP, ZIP, and AEP manager
SYNOPSIS
atalkd [-f configfile] [-1] [-2]
DESCRIPTION
atalkd is responsible for all user level AppleTalk network management. This includes routing, name registration and lookup, zone lookup,
and the AppleTalk Echo Protocol (similar to ping(8)). atalkd is typically started at boot time, out of /etc/rc. It first reads from its
configuration file, /etc/netatalk/atalkd.conf. If there is no configuration file, atalkd will attempt to configure all available interfaces
and will create a configuration file. The file consists of a series of interfaces, one per line. Lines with `#' in the first column are
ignored, as are blank lines. The syntax is
interface [ -seed ] [ -phase number ] [ -net net-range ] [ -addr address ] [ -zone zonename ] ...
Note that all fields except the interface are optional. The loopback interface is configured automatically. If -seed is specified, all
other fields must be present. Also, atalkd will exit during bootstrapping, if a router disagrees with its seed information. If -seed is not
given, all other information may be overriden during auto-configuration. If no -phase option is given, the default phase as given on the
command line is used (the default is 2). If -addr is given and -net is not, a net-range of one is assumed.
The first -zone directive for each interface is the ``default'' zone. Under Phase 1, there is only one zone. Under Phase 2, all routers on
the network are configured with the default zone and must agree. atalkd maps ``*'' to the default zone of the first interface. Note: The
default zone for a machine is determined by the configuration of the local routers; to appear in a non-default zone, each service, e.g.
afpd, must individually specify the desired zone. See also nbp_name(3).
ROUTING
If you are connecting a netatalk router to an existing AppleTalk internet, you should first contact your local network administrators to
obtain appropriate network addresses.
atalkd can provide routing between interfaces by configuring multiple interfaces. Each interface must be assigned a unique net-range
between 1 and 65279 (0 and 65535 are illegal, and addresses between 65280 and 65534 are reserved for startup). It is best to choose the
smallest useful net-range, i.e. if you have three machines on an Ethernet, don't chose a net-range of 1000-2000. Each net-range may have an
arbitrary list of zones associated with it.
EXAMPLES
Below is an example configuration file for a sun4/40. The machine has two interfaces, ``le0'' and ``le1''. The ``le0'' interface is
configured automatically from other routers on the network. The machine is the only router for the ``le1'' interface.
le0
le1 -seed -net 9461-9471 -zone netatalk -zone Argus
atalkd automatically acts as a router if there is more than one interface.
FILES
/etc/netatalk/atalkd.conf configuration file
BUGS
On some systems, atalkd can not be restarted.
SEE ALSO atalkd.conf(5)Netatalk 2.2 06 Sep 2004 ATALKD(8)