Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: Node switched itself from static to DHCP on reboot issue
Special Forums IP Networking Node switched itself from static to DHCP on reboot issue Post 302920128 by SmokeyJoe on Tuesday 7th of October 2014 11:58:18 AM
Old 10-07-2014
@Peasant Thanks for your reply. As an FYI, I have put the above question to Oracle and am waiting for a reply. This is a new x86 machine with no prior O/S installed. What makes this more of a mystery is that a further reboot (cold) invoked the original static ip?

Beadm shows default grub2 as expected:

Code:
solaris          NR     /          6.10G static 2014-10-01 08:42 
solaris-backup-1 -      -          67.0K static 2014-10-02 10:06

You raise a good point, however, on NWAM. It is my understanding that NWAM would dynamically respond to either user input or a change in network configuration. Which begs the question "what happened at re-boot"? because AFAIK nothing changed. A I am fairly new to this, what advice could you offer on which log files I should tail/interrogate. Again, many thanks.
 

10 More Discussions You Might Find Interesting

1. HP-UX

HP-UX 10.xx Changing from static IP to DHCP

***Newbie alert*** What's the easiest way to accomplish this? An admin left our company and I have taken over his HP Workstation and moved it to a different location that is on a different IP segment. I have performed a number of google searches but the steps I have followed haven't worked. ... (1 Reply)
Discussion started by: Steelysteel
1 Replies

2. UNIX for Advanced & Expert Users

problem connecting to oracle 10g after NCR node reboot

Hi All, I am facing a connection problem with Oracle 10g on Solaris 10 when my application (started by /etc/rc3.d at node reboot) tries to establish a session after reboot of the node where my application is running (NCR UNIX (MP RAS)). I find that my application (run as a deamon process)... (1 Reply)
Discussion started by: sowjanya
1 Replies

3. IP Networking

dhcp and static ip conflicts.

I have a USB Wireless Adapter using the rum0 driver. All I want to do is set a perminent static IP for the onboard wired interface elxl0. I can plumb the wired interface up fine on the fly, but when I try to save the static IP over a reboot, I lose the IP address assigned to rum0 from my wireless... (1 Reply)
Discussion started by: ts97783
1 Replies

4. IP Networking

How to configure DHCP to Static IP

I am pretty new to this. My router was earlier configured to enable DHCP, thus my UNIX box is using the dhcp address, i.e. I have to do a ifconfig dhcp hme0 start. Since I am planning to use my NT as a web server, I needed to use the static IP address. How do I configure the unix box to use the... (5 Replies)
Discussion started by: lee30320
5 Replies

5. IP Networking

Switching from DHCP to Static IP

I am trying to write a set of scripts for my Ubuntu 810 Server to allow a user to change from DHCP to a user-supplied Static IP, Subnet, Gateway and DNS Servers. So far I have the following, where $USERCHOICE is a user-entered value in each case: ifconfig eth0 down && ifconfig eth0 $USERCHOICE... (1 Reply)
Discussion started by: cleanden
1 Replies

6. Red Hat

How to know whether my system is using DHCP or STATIC IP

Hi, I am using RHEL 5.1 and i would like to know, how to find the whether my system is using DHCP or STATIC IP with out looking at /etc/sysconfig/network-scripts/ifconfig-eth0 configuration file. Regards, Venkat (3 Replies)
Discussion started by: venkat55
3 Replies

7. UNIX for Dummies Questions & Answers

How to tell if i am using DHCP or Static

Hey guys , YEs this is probably silly for most but i am new to this forum and solaris . i am curious to know if the ip address we have for our solaris server is static or dhcp . how can i tell ? will ifconfig -a tell me this ? or other commands? Thanks in advance (1 Reply)
Discussion started by: xdrivex
1 Replies

8. Red Hat

Purpose of Static IP address through DHCP

Hi All, Could you please explain the purpose of assigning the static IP by using the DHCP Concept. Like by using the clients MAC address we assign the static IP Address. Waiting for your reply. Thanks in Advance. (6 Replies)
Discussion started by: Sharath Kumar
6 Replies

9. HP-UX

[Solved] Static or DHCP IP in HP-UX

Hi, I can find the IP details whether it is Static or dynamic in Linux machine from the location /etc/sysconfig/network-scripts/ifconfig-eth0 configuration file. Can someone suggest a location to find the same in HP UX machines? -Vivek (2 Replies)
Discussion started by: vkk
2 Replies

10. Solaris

Solaris static IP changed (non DHCP)

We have 2 solaris 10 t5240 servers with static IP addresses on nxge0 I/F which were rebooted a few days back with a known good config that has been in place for years (for /etc/hosts, /etc/hostname.nxge0, /etc/netmasks, etc) They are not using dhcp. About the same time today, both of their... (7 Replies)
Discussion started by: hdatontodo
7 Replies

LEARN ABOUT HPUX

install-solaris

install-solaris(1M)													       install-solaris(1M)

NAME

       install-solaris - install the Solaris operating system

SYNOPSIS

       install-solaris

       install-solaris	invokes  the  Solaris  Install	program. Depending on graphical capability and available memory at the time of invocation,
       install-solaris invokes either a text-based installer or a graphical installer.

       The following minimum requirements for physical memory dictate which features are available during installation:

       For SPARC machines:

       128 MB

	   Minimum physical memory for all installation types

       128 MB

	   Minimum physical memory required for windowing system

       384 MB

	   Minimum physical memory required for graphical-based installation

       For x86 machines:

       256 MB

	   Minimum physical memory for all installation types

       256 MB

	   Minimum physical memory required for windowing system

       512 MB

	   Minimum physical memory required for graphical-based installation

       In some cases, even if the minimum physical memory is present, available virtual memory after system startup can limit the number  of  fea-
       tures available.

       install-solaris	exists	only  on  the Solaris installation media (CD or DVD) and should be invoked only from there. Refer to the  for more
       details.

       install-solaris allows installation of the operating system onto any standalone system. install-solaris loads the software available on the
       installation media. Refer to the  for disk space requirements.

       Refer to the  for more information on the various menus and selections.

       See attributes(5) for descriptions of the following attributes:

       +-----------------------------+-----------------------------+
       |      ATTRIBUTE TYPE	     |	    ATTRIBUTE VALUE	   |
       +-----------------------------+-----------------------------+
       |Availability		     |SUNWcdrom  (Solaris instal-  |
       |			     |lation media)		   |
       +-----------------------------+-----------------------------+
       |Interface Stability	     |Evolving			   |
       +-----------------------------+-----------------------------+

       pkginfo(1), install(1M), pkgadd(1M), attributes(5)

       It is advisable to exit install-solaris by means of the exit options in the install-solaris menus.

								    23 Sep 2005 					       install-solaris(1M)
All times are GMT -4. The time now is 06:36 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy