Hello! I have some trouble trying to configure a VPN with two gateways. One of them uses IPSec with a single key, 256bits length, specified in /etc/ipsec.secrets. As FreeSwan manual page says, if i put esp=3des-md5-96, will be used a "64bit IV key (internally generated), a 192bit 3des ekey and a... (3 Replies)
Setup a site to site VPN between two cisco routers.
One of the site locations is unable to access ports such as https://example.com:9001
How do I let them go into port 9001?
They can ssh, ftp, telnet and everything else.
Is this a VPN issue or ACL access issue?
I put
permit ip host... (0 Replies)
Hello,
I'm trying to setup a gateway VPN between two routers across an unsecured network between two local networks. The routers are both linux and I'm using the ipsec tools, racoon and setkey. So far hosts from either local net can successfully ping hosts on the other local net without issue.
... (0 Replies)
Hi,
I am trying to establish vpn between my linux server and cisco asa at client side.
I installed openswan on my cent os.
Linux Server
eth0 - 182.2.29.10
Gateway - 182.2.29.1
eth1 - 192.9.200.75
I have simple IPtables Like
WAN="eth0"
LAN="eth1" (0 Replies)
Q: "Does Cisco 1921 router support,, act as an endpoint for, site to site VPNs using IPSec? If so, how many? "
A: If you get the Cisco 1921/k9 with the security services bundle then it will have built in security features. Cisco, typically includes IP Sec tunnels I believe as part of that... (0 Replies)
Hi all,
I have installed Openswan and configured IPSec and works perfect, but for some unknown reasons it stop working. I see that the tunnels are up and established. The route to the destination are added. Everything by the book seems to be ok. But somehow when i start to ping the other side (... (4 Replies)
We are using cyberoam device, VPN IPSEC tunnel is going of frequently even the traffic is throug.
Please suggest what may be the cause for the above mentioned issue.
Also suggest a best tool to monitor the same VPN IPSEC tunnel connectivity. (4 Replies)
Hello, I am new here and my name is Robert. I was actually looking for a forums website where I can go with questions regarding Linux and embedded Linux applications. I am fairly new (6 months) to the world of Linux and embedded Linux applications and the the learning curve is steep. When I am not... (13 Replies)
Discussion started by: Circuits
13 Replies
LEARN ABOUT DEBIAN
prips
PRIPS(1) BSD General Commands Manual PRIPS(1)NAME
prips -- print the IP addresses in a given range
SYNOPSIS
prips [-c] [-d delim] [-e exclude] [-f format] [-i incr] start end
prips [-c] [-d delim] [-e exclude] [-f format] [-i incr] CIDR-block
prips -h
DESCRIPTION
The prips tool can be used to print all of the IP addresses in a given range. It can enhance tools that only work on one host at a time,
e.g. whois(1).
The prips tool accepts the following command-line options:
-c Print the range in CIDR notation.
-d delim
Set the delimiter to the character with ASCII code delim where 0 <= delim <= 255.
-e <x.x.x,x.x>
Exclude ranges from the output.
-f format
Set the format of addresses (hex, dec, or dot).
-h Show summary of options.
-i incr
Set the increment to 'x'.
ENVIRONMENT
The prips tool's operation is not influenced by any environment variables.
FILES
The prips tool's operation is not influenced by any files.
EXAMPLES
Display all the addresses in a reserved subnet:
prips 192.168.32.0 192.168.32.255
The same, using CIDR notation:
prips 192.168.32/24
Display only the usable addresses in a class A reserved subnet using a space instead of a newline for a delimiter:
prips -d 32 10.0.0.1 10.255.255.255
Display every fourth address in a weird block:
prips -i 4 192.168.32.7 192.168.33.5
Determine the smallest CIDR block containing two addresses:
prips -c 192.168.32.5 192.168.32.11
DIAGNOSTICS
The prips utility exits 0 on success, and >0 if an error occurs.
SEE ALSO ipsc(1), gipsc(1)STANDARDS
No standards were harmed in the writing of the prips tool.
HISTORY
The prips tool was originally written by Daniel Kelly and later adopted by Peter Pentchev. This manual page was originally written by Juan
Alvarez for the Debian GNU/Linux system and later added to the prips distribution and converted to mdoc format by Peter Pentchev.
AUTHORS
Daniel Kelly <dan@vertekcorp.com>
Juan Alvarez <jalvarez@fluidsignal.com>
Peter Pentchev <roam@ringlet.net>
BUGS
Please report any bugs in the prips tool to its current maintainer, Peter Pentchev.
BSD March 1, 2011 BSD