10-03-2014
Quote:
Originally Posted by
jim mcnamara
I
Are there required MIB lists missing as a startup parameter for snmpd?
Thank you, Jim.
In fact all the MIB settings are in place (this is basically what the mentioned entries in
/etc/snmpdv3.conf do) and the quoted line with the
snmpinfo command proves that snmp is up and working as expected. I could have (and in fact - have) started
snmpwalk instead and it shows the whole MIB tree for HACMP being in place. The listing is quite long so i didn't post it but in fact it is there.
In addition, if SNMP would not be configured correctly in respect to HACMP then the
cldump should also not work, but does so. This is why i believe that SNMP is not the problem here but it is
the common problem if
clstat is not working so i posted the respective info beforehand.
bakunin
Last edited by bakunin; 10-03-2014 at 05:58 PM..
10 More Discussions You Might Find Interesting
1. AIX
Hello,
I was wondering if I have 3 nodes (A, B, C) all configured to startup with HACMP, but I would like to configure HACMP in such a way:
1) Node B should startup first. After the cluster successfully starts up and mounts all the filesystems, then
2) Node A, and Node C should startup !
... (4 Replies)
Discussion started by: filosophizer
4 Replies
2. AIX
This post just as a follow-up for thread https://www.unix.com/aix/115548-hacmp-5-4-aix-5300-10-not-working.html: there was a bug in the clcomdES that would cause the Two-Node-Cluster-Configuration-Assistant to fail even with a correct TCP/IP adapter setup. That affected HACMP 5.4.1 in combinatin... (0 Replies)
Discussion started by: shockneck
0 Replies
3. AIX
Hi
What is the procedure to upgrade the MQ from 6 to 7 in aix hacmp cluster. Do i need to bring down the cluster
services running in both the nodes and then give #smitty installp in both the nodes separately. Please assist... (0 Replies)
Discussion started by: samsungsamsung
0 Replies
4. AIX
Hi all,
I was wondering if someone direct me in how to Make system backup for 2 nodes HACMP cluster ( system image ) .
What are the consideration for this task (3 Replies)
Discussion started by: h@foorsa.biz
3 Replies
5. AIX
Hi,
I have a IBM Power series machine that has 2 VIOs and hosting 20 LPARS.
I have two LPARs on which GPFS is configured (4-5 disks)
Now these two LPARs need to be configured for HACMP (PowerHA) as well.
What is recommended? Is it possible that HACMP can be done on this config or do i... (1 Reply)
Discussion started by: aixromeo
1 Replies
6. AIX
Hi
I'm a little rusty with HACMP, but wanted to find out if it is possible to remove a disk heartbeat network from a running HACMP cluster.
Reason is, I need to migrate all the SAN disk, so the current heartbeat disk will be disappearing. Ideally, I'd like to avoid taking the cluster down to... (2 Replies)
Discussion started by: cmcbugg
2 Replies
7. AIX
As i have updated a lot of HACMP-nodes lately the question arises how to do it with minimal downtime. Of course it is easily possible to have a downtime and do the version update during this. In the best of worlds you always get the downtime you need - unfortunately we have yet to find this best of... (4 Replies)
Discussion started by: bakunin
4 Replies
8. AIX
Hi,
A customer I'm supporting once upon a time broke their 2 cluster node database servers so they could use the 2nd standby node for something else. Now sometime later they want to bring the 2nd node back into the cluster for resilance. Problem is there are now 3 VG's that have been set-up... (1 Reply)
Discussion started by: elcounto
1 Replies
9. AIX
Hi all,
I remember way back in some old environment, having the HA cluster services not being started automatically at startup, ie. no entry in /etc/inittab.
I remember reason was (taken a 2 node active/passive cluster), to avoid having a backup node being booted, so that it will not... (4 Replies)
Discussion started by: zaxxon
4 Replies
10. AIX
HACMP two-node cluster with mirrored LVM.
HACMP two-node cluster with two SAN storages mirrored using LVM. Configured 2 disk heartbeat networks - 1 per each SAN storage. While performing redundancy tests. Once one of SAN storage is down - cluster is going to ERROR state. What are the guidelines... (2 Replies)
Discussion started by: OdilPVC
2 Replies
LEARN ABOUT CENTOS
crm_node
PACEMAKER(8) System Administration Utilities PACEMAKER(8)
NAME
Pacemaker - Part of the Pacemaker cluster resource manager
SYNOPSIS
crm_node command [options]
DESCRIPTION
crm_node - Tool for displaying low-level node information
OPTIONS
-?, --help
This text
-$, --version
Version information
-V, --verbose
Increase debug output
-Q, --quiet
Essential output only
Stack:
-A, --openais
Only try connecting to an OpenAIS-based cluster
-H, --heartbeat
Only try connecting to a Heartbeat-based cluster
Commands:
-n, --name
Display the name used by the cluster for this node
-N, --name-for-id=value
Display the name used by the cluster for the node with the specified id
-e, --epoch
Display the epoch during which this node joined the cluster
-q, --quorum
Display a 1 if our partition has quorum, 0 if not
-l, --list
Display all known members (past and present) of this cluster (Not available for heartbeat clusters)
-p, --partition
Display the members of this partition
-i, --cluster-id
Display this node's cluster id
-R, --remove=value
(Advanced) Remove the (stopped) node with the specified name from Pacemaker's configuration and caches
In the case of Heartbeat, CMAN and Corosync 2.0, requires that the node has already been removed from the underlying cluster
Additional Options:
-f, --force
AUTHOR
Written by Andrew Beekhof
REPORTING BUGS
Report bugs to pacemaker@oss.clusterlabs.org
Pacemaker 1.1.10-29.el7 June 2014 PACEMAKER(8)